NTM Prop unidade Series 42-58 500kV / 1300W

• Overall
• Quality
• Value

Customer Rated

Aug 07, 2016

Ich habe 2 Motoren gekauft zu unterschiedlichen Zeitpunkten. Betreibe beide Motoren mit einem 60A YEP und einem 13x6,5 Prop in einer Canadair 2005mm Spannweite. Beide Motoren haben Kontaktprobleme. Habe alle Kontakte mehrfach nachgelötet. Trotzdem waren es nicht die Kontakte sondern die Wicklungen, die nach etwa 2 Minuten, bei erneutem Motoranlauf Kurzschlüsse in den Wicklungen verursachen. Vermutlich an den Kabelausgängen direkt am Motor. Auch nach Videobeweis ist HK anscheinend nicht in der Lage EINFACHSTE PROBLEME zu erkennen. Leider - Folge RMA mal sehen wie sie sich diesmal anstellen werden? Vermutlich hat auch der Regler einen wegbekommen.

• Overall
• Quality
• Value

Customer Rated

Jul 30, 2016

nice motor , got this in a PA MX on 6s 2200mah , loads power , gr8 for the $$ , good value so far , just a little heavier that the Thrust 50 i have in another PA MX air frame

• Overall
• Quality
• Value

Customer Rated

Jun 23, 2016

J'ai monté ce moteur sur un planeur de 5kgs et accus 5000 6s avec une hélice de 15x8 je crois; Au début, il chauffait un peu mais après avoir percé 2 trous dans le fuselage, il va bien; Puissant et ne chauffe plus. Servi 4 vols et pour l'instant, j'en suis bien content.

• Overall
• Quality
• Value

Customer Rated

Jun 10, 2016

Very disappointed. Motor threw armature windings after less than 2 months use and approximately 25 flights. Now scrapped. Using 6 cell battery, 14x10, 15x7 or 15x8 prop.

• Overall
• Quality
• Value

Certified Buyer Rated

May 24, 2016

très bon moteur je le recommande pour le piper L4 hk avec hélice 15x8 turnigy light wood et accus 6s 5000 mah avec ce moteur beaucoup de puissance merci HK

• Overall
• Quality
• Value

Certified Buyer Rated

May 09, 2016

Big motor! Really it is smaller then I imagined, but it has a nice power/weight ratio.

Make attention the rotor is 'inversed'

• Overall
• Quality
• Value

Customer Rated

Apr 29, 2016

It is an very nice motor just make sure you always stay below the max current of 70A otherwise the magnets will come loose. I use this motor in all my 3D 60"planes but I don't run them stock (I re-glue the magnets). On 6S with a 16x6 Turnigy lightwood prop:
Max Power slightly above 1400W
Max current=71A

Motor performance and info can be checked in one of my build threads on RCG:
http://www.rcgroups.com/forums/showthread.php?t=2477069
My tips for re-glueing magnets:
http://www.rcgroups.com/forums/showthread.php?t=2357100

• Overall
• Quality
• Value

Customer Rated

Jan 29, 2016

I read the reviews on this motor and glued the magnets before I used it for the first time. So far so good. I did hit a couple of problems. 1) The shaft was out of alignment so there was a wobble when it spun. I thought the prop adapter was the problem but it turned out the motor case where you bolt the prop adapter is not perpendicular to the shaft. I had to add a VERY thin shim to one side behind the prop driver before I bolted it down. 2) There is NO WAY the prop test data for this motor is correct. It says 15x8 - 22.2v - 1256W - 56.6A. NO WAY! I am running on a 6S pack and with a 15x8 is wants to pull something crazy like over 80A! Turnigy Plush 100A ESC and Turnigy Nanotec 6S 45C. I had to pull the end point adjustment of the throttle channel back to 50pcnt to get close to 60A so I was not pumping more than 1300W through this motor. Be careful with prop selection with this motor as it is 500kV so that means 11,300 RPM on 22.6V. A 15 x 8 is going to need more than 1300W to spin that fast. My 2c.

• Overall
• Quality
• Value

Customer Rated

Dec 04, 2015

I bought one of these NTM42-58 500kv 1300W motors to put in my T6 Texan ii from Phoenix Models. I bought it instead of the recommended Rimfire .46 or .55 motor in the kit. The kit calls for a motor in the 1000W to 1400W range. At a 1/3 the price this motor is amazing. The T6 Texan is 8.5 lbs and using a 14x8.5E prop I get great performance from the motor. It is coupled with a Turnigy 85A ESC w/5A SBEC and a Turnigy 6s 5000mAh 25c battery. This power setup is more than enough power to fly the T6. This is my first NTM motor so time will tell how it holds up. I have a wattmeter coming to measure the power draw, but so far nothing is warm after I fly for 5 mins. I would definitely get one of these for any 60 size airplane. This is a great motor and I will by buying other NTM motors in the future.

• Overall
• Quality
• Value

Customer Rated

Jul 31, 2015

Awesome product! I'm running it in my Sbach 342 60E with a 15X8 turnigy lightwood prop and Zippy Compact 6S 3300mAh/ 35C. Unbelievable insane power!
This motor came with a retaining ring for the magnets which should prevent them to come loose.
I will update this review later with wattmeter test data.