Pedal Assembleia auto Operado Bungee Sistema de Lançamento / Rampa para FPV / planador e FED Models - lançando mão de modelos pode ser um negócio complicado ea maioria dos folhetos ter tido tudo dar errado para eles em algum momento, este grande sistema de lançamento é fácil de transportar e de campo montar e permite o lançamento totalmente solo com a paz de espírito de velocidade aerodinâmica adequada de cada vez para um lançamento bem sucedido, tudo o que você precisa está incluído!
Dimensões Uma vez montado:
Comprimento rampa - 1.060 milímetros
altura na traseira - 240 milímetros
altura na frente - 460 milímetros
largura de trilhos de lançamento - 470 milímetros
Ramp - Tubing GF com Marceneiros de plástico
Pé Sistema de Lançamento - Ply com mangueira de borracha cirúrgica (2 metros)
Características do Produto
Peso ( g )
Unit was unable to be assembled. Apparently they changed to a thicker plywood but neglected to enlarge the square holes the pivot ears mount into. Either that or the kerf allowance is far off. Completely useless without spending an hour filing. I'll build from scratch in that case.Update, I will load the picture of my finger to the files tab. Don't know if they will let me post it. WARNING! VERY GRAPHIC!Please be very careful with this item! It does misfire often unless you modify it or create a safety device for the release. I had to go to the Emergency Room last night and have the metal ring that is the release ring to the foot pedal surgically removed from my right index finger! I was loading the jet onto the stand with the release ring on the post for the foot pedal, and being very careful because it does literally misfire twice as much as it releases an airplane, and it let loose. That metal ring, literally pierced through my finger and I had to run towards the large nail that holds the other end of bungee because it was trying to pull the ring out of my finger! The gap where to formed ring comes together is only as wide as a piece of paper, but some how that was enough to grab a piece of my skin, and it pulled itself right through one side of my finger and out the other side! I sure wish I could post the pictures on this review! it is a very graphic picture but it sure would make HK rethink the design! This device needs to be modified like the other review to make some what safe for use! I'm 40 years old and have been in modeling for many decades. This thing is dangerous!Here's the short review: Best catapult you can buy for 22 EUR. More details: Works reasonably well, I'd suggest a few modifications. Use LOTS of superglue on all frame joints. tie the release plate to the bottom of the fiber glass pipe, not the top. Use a dremel or metal saw to roughen up the pin in the release mechanism, it is really slick. Use a small key ring to hook in your plane. Make sure that the hook is glued VERY securely, due to the catapult's design, the full draw force of the sling rips into the plane. For a Radjet 800, I used about 7m of draw length -> Get a longer rubber if you don't have impressively good reflexes.Vorweg, mit 20 kann man hier nichts falsch machen.
Wie aber leider schon angesprochen, fehlt es an einer Anleitung.
Das ist beim Bau nicht so tragisch, aber bei der Inbetriebnahme schon.
Man weiss erst nicht, wie man das Seil und das Gummi verbinden muss, auch nicht welche Lnge man braucht, wenn man ein strkeres Gummi nimmt.
Hat man dies einmal raus geht es eigentlich ganz gut.
Die Halterung am Flugzeug ist etwas schwerer.
Bei meinen ersten Versuchen, zog das Gummi den Flieger wieder zu Boden.Overall nice product. I modified my Go Discover to be bungee launched like my RV Jet. I did change out the nails with tent spikes as the ground here is a little hard. I also modified the pedal by drilling a 7/64th hole to install a safety pin to prevent accidental releases.other than that, it does well.unless you live out in the woods do yourself a favor and go to home depot and 8 elbows and one ten foot lengh of 3/4 " pvc pipe and build it yourself. It's a cheap POSToday I launched my Taborca 3.30 m. flying wing sailplane with this system; works really good, in stead of the included rubber hose I used 10 meter of 5 mm bungee cord, this will launch a glider this size no problem. Just remember to not start the motor before the bungee drops from the hook as the prop will cut it... Taborca is hard to handlaunch as the CG is far back on the fuse (swept wing), this ramp solves a problem.
Construction might be tougher, and it would be real handy if this ramp could be folded over or disassambled!this cheap by far and does come with its niggles but out of the box ready to use and i have done many launches on it, reason i give 4 stars is because the bungee cord that comes with it does not have a lot of force, so if you inted to use a bigger edf with more airspeed requirements, i would advise to buy extra bungee cordFrame is OK but included bungees are way too short for practical launch of any aircraft.