O Skyfun pode ser usado por novatos e pilotos avançados. Com uma velocidade máxima de cerca de 120 kmh e uma velocidade de estol lento, o Skyfun é um jet-parque você vai querer tomar em toda parte.
Feito com EPS de alta pressão e um molde polido, o Skyfun é extremamente duro, tem uma superfície brilhante lisa com aplicada a fábrica dos gráficos e ainda é muito resistente acidente!
Esta é a nova versão atualizada (v1.1) do SkyFun - tem agora montar um motor de liga mais forte e um motor 2500kv ao invés do 1800kv do original.O que isto significa? Mais velocidade em linha reta e mais poder fora da caixa!Especificação:Envergadura: 875 milímetrosComprimento: 700 milímetrosAltura: 170 milímetrosVoar Peso: 550gMotor: 2500kv Brushless OutrunnerESC: 25AServo: 2 x 9g
Guia de criação (em CD)
Adesivo epóxiRequeridos:Seu próprio TX e RXBateria 1300mAh 11.1V 3S 20C ou superior
Características do Produto
Capacidade ( mAh)
Peso ( g )
I got this plane without any user manual,without glue,without wing support
It is made from very bad epo foam,it can be broke easly
On my first test,i hold it in my hand (lucky)motor was burned and smoked up for half minute on half throttle
This is very very bad and i do not recomend itThis was a quick and easy build with no need for instructions! I have been flying mine on 1300mAh 3S 25-50c batteries and can easily get in 10 minutes of flight time because this model flies so well at low speeds. One of the best deals on HK!Plane arrived without damage however the epoxy had leaked into the bag coating the prop and servo covers but it came off easily with a little spirit and a touch of Gorilla Glue worked as well as the epoxy. The build was simple (I bought the plug and fly version), just attach the wings and fins, insert a receiver and battery.....that's about it. Looks great, flies well.One of my favourite models that I own. Its main merit is its diversity, in that it tracks very well and can fly almost like a trainer with 60/40 or 70/30 DR and Expo, but it can also perform some crazy aerobatics, with a monumental roll-rate on 100pcnt rates. I find this plane a joy to fly for thrills or just for a relaxing fly.
My main (if not only) criticism of the Skyfun Jet is that the canopy clips do a very poor job of holding the canopy on, and will give way after a few rolls (which resulted in my canopy getting slightly chopped!). A cheap fix for this is just putting 3 squares of velcro on the model, and 3 corresponding squares (soft or rough for both, not different) on the canopy (I did one at the nose and 2 at the back end), and then using a strip of the other part (rough if soft on body, vice versa) to connect the two.
This plane is also very comfortable for landing, and is ideal for someone just entering the intermediate category.
I have owned two of these in total, my first when I just entered intermediate stage, and one now with a souped-up power set. It is a great learner plane and can build confidence and skill!Took me all of 10 minutes to glue together. Brilliant!. Comes in 5 pieces and requires nothing other than glue to attache the wings and fins. I pinned the canopy down by pushing a bamboo skewer through the fuselage. This is a great aircraft and flies equally well slow or fast. 3s 1300 gives plenty of power, even enough to give unlimited vertical. Cut the power and this thing will glide forever! It' as much fun to fly as a Stryker and a fraction of the price. I've seen one fitted with a 4s lipo but be careful if you do this - the elevon hinges may need reinforcing. The one is saw had an elevon detach in flight which caused a terminal crash.
my order arrived ok and on time no probs so far !!!
On first inspection it seemed OK until I decided to put it together.
The Canopy perspex cover just fell off
The two part adhesive that was supplied was well past it's sell by date and was no where near enough to complete the model
The motor was loose and very noisey
No carbon fibre reinforcement rods were supplied
The servo covers were useless and very poor fit
Typical cheap hobbyking rubbish
After several mods I'm optimistic it might fly
Ideal first pusher evelon model. Apart from adding a 6x1mm carbon flat I'm flying mine stock. Maiden flight (see video tab) completed without drama as she hand launches easily. Aerobatic enough with the stock tape hinged control surfaces but I can see the need for something beefier if you up the power. Great slow speed and glide performance and I'd imagine that the airframe could easily handle more weight. Should make a good stable platform for my Mobius action camera. You won't regret purchasing the model and if you get board with the stock set up then there are lots of hop up's possible.This Skyfun is really a fun plane to fly. I log close to 300 flights on this plane. Fly characteristic is amazing fast and accurate. After the first 80 flights, I up grade to recommended motor Turnigy 2836-2350kv wth ESC Turnigy Plush 60A https://www.youtube.com/watch?v=Vgh-G6MkUNs. Now this thing is shooting straight up into the sky with unlimited vertical climb. I have purchase a second Skyfun as a backup in case the first one get damage.
This plane flys awesome but really does need work otherwise it wont last more than a few flights.
Where do I start, motor mount was lose so make sure you sheck it, the ailerons were taped on badly and flexed like hell so I removed them then hinged them and added CF rods within the ailerons which worked very well. Ailerons were warped which needed straightening. Wing servo covers are to shallow, modding required. Servo mounts inside wings need re gluing. Alot of ppl say the canopy latches are not good or safe but mine now holds well after a simple fix. No instructions, not that any are needed. All edges need a light sand due to rough finish. The Prop was unbalanced and had about 3 mm play with the prop adapter, so a prop spacer will be needed. Do all these things and you will have an awesome fast flyer with incredible slow landings. DO NOT power up this plane prior to checking and fixing the prop/adaptot/motor mount what ever you do! Thats very unsafe for HK to ship out items like this. Better off leaving it all in pieces so a newbie does not make the mistake of trusting "factory built and tested' products.spot on plane ailerons could do with being a bit stiffer flying it on a 2200 mah with out any probs ordered a new motor now as I want a bit more speed nice stable flyer with the stock motor im going to change the ailerons for wood but originals are ok ive out carbon rod in the wings these are pre cut ready and put tape on the leading edge and under the bottom canopy fixings not the best in the world ive put a small carbon rod in the canopy front to make sute it don't come off in flight but all in all a great model to fly and would recommend it anybody
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
Skyfun anti flap mod download now [515kb] Skyfun anti flap mod download now [484kb] Skyfun anti flap mod download now [500kb] Skyfun anti flap mod download now [440kb] Skyfun anti flap mod download now [427kb] Skyfun anti flap mod download now [597kb] Skyfun anti flap mod download now [469kb] Skyfun anti flap mod download now [513kb] Skyfun anti flap mod download now [513kb] Skyfun anti flap mod download now [578kb] Skyfun with landing gear download now [1506kb] No File Name download now [1506kb] max amps and watts measure download now [494.96Kb]