New Items Forum
Registar

Total Price

0,00 €

Carrinho 0 Carrinho 0 Loading...

Super Bright 3Watt Branco Lâmpada LED com alumínio dissipador de calor

Super Bright 3Watt Branco Lâmpada LED com alumínio dissipador de calor

Discontinued Product

Please continue searching for a similar product.
Peso:
6 g
SKU:
371000040
WANT FREE SHIPPING? Click here to find out more!
Este Super Bright 3 watt LED branco vem montado em um dissipador de calor de alumínio e é pré-wired com um conector estilo JR.

Perfeito para vôo noturno!

Spec:
Entrada: 2,5-3 volts
Cor: Branco
Brilho: 70-80 Lumens
Diâmetro: 20mm
Peso: 4g
  • SKU 371000040
  • Brand -
  • Capacidade ( mAh) -
  • Peso ( g ) 6.00
  • Comprimento 30.00
  • Largura 20.00
  • Altura 30.00
  • RGB LED Boards & Strips
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Great price, very bright for about 5 minutes until I let the smoke out of them lol. My fault, I'm running 3w red led strip along the bottom of my nighthawk build and 2 of these mounted at the bottom front for headlights. I bought them a while back and finally decided to install them. They don't like 12v LOL, totally my fault. Probably buy some more and step down to 3v like stated.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great price, very bright for about 5 minutes until I let the smoke out of them lol. My fault, I'm running 3w red led strip along the bottom of my nighthawk build and 2 of these mounted at the bottom front for headlights. I bought them a while back and finally decided to install them. They don't like 12v LOL, totally my fault. Probably buy some more and step down to 3v like stated.

2.5 volts max as they get very hot on higher voltage. Much brighter than the strip LEDs of 12v.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

2.5 volts max as they get very hot on higher voltage. Much brighter than the strip LEDs of 12v.

Bought two, blew one up carelessly by putting it on the same circuit as my 12V strip lights, the other one is going strong. Maybe I got an especially good one, but this LED withstands 5V without issue (it does get hot to the touch, though).

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Bought two, blew one up carelessly by putting it on the same circuit as my 12V strip lights, the other one is going strong. Maybe I got an especially good one, but this LED withstands 5V without issue (it does get hot to the touch, though).

I put three in parallel and hooked them up to a 3S they put out an instense light, i am yet to run them long term but its on the project list

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I put three in parallel and hooked them up to a 3S they put out an instense light, i am yet to run them long term but its on the project list

Does not come with connector. Fairly big for what I wanted. Probably would be ok with a different setup. Just not for me.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Does not come with connector. Fairly big for what I wanted. Probably would be ok with a different setup. Just not for me.

indeed this is a light , very impractible being 3.6max volts

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

indeed this is a light , very impractible being 3.6max volts

un beau petit phare d'attero pas trop gros

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

un beau petit phare d'attero pas trop gros

Using with 10 ohm resistor on 12v supply as headlight for my ebike. This LED puts out quite a bit of light! It's about the same as my motorcycle's low beam. I'm going to add a couple more later on for extra light. Note that you'll need a bigger heatsink to go above 1 1/2 watts. I pulled one off the northbridge chip on a dead motherboard and used thermal compound mixed with epoxy in a very thin layer to glue it on. Using my IR temp gun the LED is only a couple degrees above the heatsink after 5 minutes so the thermal conductivity is good.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Using with 10 ohm resistor on 12v supply as headlight for my ebike. This LED puts out quite a bit of light! It's about the same as my motorcycle's low beam. I'm going to add a couple more later on for extra light. Note that you'll need a bigger heatsink to go above 1 1/2 watts. I pulled one off the northbridge chip on a dead motherboard and used thermal compound mixed with epoxy in a very thin layer to glue it on. Using my IR temp gun the LED is only a couple degrees above the heatsink after 5 minutes so the thermal conductivity is good.

Very bright little light, have it hooked up to 2x 1.5v AA's. Great landing light or navigation light.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very bright little light, have it hooked up to 2x 1.5v AA's. Great landing light or navigation light.

Easy to use bright led, wires is about 10 cm long 1,5 cm connector. it gets warm from 3,3 volts but it not burn hands when you hold it.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Easy to use bright led, wires is about 10 cm long 1,5 cm connector. it gets warm from 3,3 volts but it not burn hands when you hold it.

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. ...
  7. 7
Customer files
No File Name Download [191]
led driver board Download [1556]
led driver board Download [1556]
Voltage Current Table Download [82]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!