Registar

Product Finder

Definições

Useful links

Bate-papo ao vivo
 
[["US","AU","GB","DE"]]
Registar

Alvo Drone Fiberglass FPV Plataforma 1.520 milímetros (ARF)

Alvo Drone Fiberglass FPV Plataforma 1.520 milímetros (ARF)

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Peso:
1450 g
SKU:
189000058

Combine

essential items and
esc
battery
servo
motor
acc
Descrição
do

O alvo não tripulado é uma grande plataforma FPV pouco que foi especificamente concebido para o trabalho e não só é o kit mais barato para comprar, este grande modelo pouco também é barato para entrar no ar.

O alvo não tripulado apresenta uma fuselagem FG que é aberto na frente para a montagem da câmera, há também um construído em cobertura anti-reflexo. O modelo é projetado para um motor propulsor como seria de esperar e também possui um MID montada, grande portal para a bateria e equipamentos de acesso, o grande e aberto área de fuselagem não só tem muito espaço para o seu equipamento FPV e lipoly, ele também fornece abundância de bateria e resfriamento ESC da fuselagem da frente aberta. A carruagem inferior é robusto, com parafuso em liga de perna de na parte traseira e uma roda de nariz orientável na frente.

O alvo não tripulado é uma compilação muito rápido, cabos de extensão servo são pré-instalado na asa balsa, que é montado em uma haste CF e epoxied no lugar. O hardware fornecido é comprensive e as partes globais contar de baixo, o que significa que você estará experimentando FPV em tempo rápido de casal. O alvo não tripulado, com ele é tailess, asa varrida é um dos modelos EP FPV mais incomuns e interessantes em sua classe ainda e é certo para chamar a atenção das pessoas, sempre que ele voa!

Características:
Robust FG Fuselagem
Abrir Câmara Frontal Monte com anti-reflexo Tampa
Grande Mid-Mounted escotilha de acesso
Balsa Construído Asa & Winglets
Resistente Sob Carriage
Nose-Wheel Steerable
Baixa contagem das peças
Todo o hardware incluído
Configuração Pusher

especificações:
Envergadura: 1,520 milímetro
Comprimento: 500mm
Voar Peso: 500g ~ 700g
Área Wing: 17.2dm2
Asa Loading: 29g / dm2 ~ 40.6g / dm2

exige:
Sua própria 4 ~ 6 Canal TX / RX com Elevon Misturando
1800kv 28-36 Brushless Outrunner Motor
3 x Servo 9g
30A ESC w / BEC
Bateria 1300mAh ~ 2200mAh 3s Lipoly
Equipamento FPV

Product
Specifications

Características do Produto

  • SKU:
    189000058
  • Brand:
    N/D
  • Peso ( g )
    1450.00
  • Comprimento
    850.00
  • Largura:
    140.00
  • Altura:
    180.00
Community
Discussions
Rate&
Review

Escreva a sua análise

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
The plane flies very well, if you set the correct CG. (250mm from the rear edge) The downside - very heavy landing gear. Buy the right carbon 120mm height. Fold back the front landing gear, otherwise it will tear off landing))) Good luck!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Its very small and looks crap. I dont know how you fly this thing. You can probably build something like this at home.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Target Drone flies :-). And its very fast. Quality is good, but neet to be sreghten Nose Wheel. Hers My maiden flight video - http://www.youtube.com/watch?v=DsXqzUnCIgg&list=UUgu1IJ5NXcCydNS76izSDDw&index=1&feature=plcp
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
The target drone does fly it does require quite a bit of work to get it into the air with setting of wing incidence twisting of the wings and recalculating the CG. With the wing design it flies quite fast. I have been working on this now on and off for two weeks and will have another test fly this week-end. What is needed is at least another Target drone to optomize the the wing incidence and CG settings so that I can have confidence in the final setup. For those wanting to experiment the starting point is as follows: wing incidence 2 degrees positive at root - wing twisting to Zero degrees at tip, CG 125 - 128mm behind leading edge at root.



Good Luck

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
The good: Quality and Value exceptional - Mine arrived well packaged with no damage, the plane went together well, and apart from a bit of mucking around on the nose wheel it was really good. I beefed up the nosewheel and the fiberglass around the wing mounting and glued the wings in. Was planning on mounting the motor internally however there wasnt enough room to play with installing it. Installed recommended motor, 45A ESC and micro servos as well as FPV pan/tilt camera setup and tx.
The Bad: 3 failed attempts at maidening this plane, have tried the middle of the recommended C of G as well as both extremes and every time it lunged vertically on take off, stalled, and then fell on its back.

If this plane flew and was stable it would be a solid 5/5 but until that time it is completely unflyable. Hopefully someone gets this sorted and can report on the right C of G, until then mine will be gathering dust which is a shame for such a nice looking model.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Really catch looking model, but not for beginners. Would be nice to have the front wheel hole pre-drilled. Wings have to be glued on.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
not bad but a little week in the front and the wheal will fold on landing . , all out ,difficult to use as a reliable FPV ,and is not a slow plane.,
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Received mine in good condition.
No instruction on where the CG should be.
Based on CG calculator about 188mm from front leading edge.
Nose heavy with 2200 3S lipo.
Ready to maiden, but i think I will need the flight stabilizer to maiden it.

verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This is just a manufacturing and packaging review... I still have to fly it.



1 stars, both wings have the tip bumped and there is also some bump here and there in the top surface.



One wing has the hole for the carbon rod closed by excessive glue usage (I will have to drill it hoping that there is not glue also deep inside the hole where my drill can't arrive).



The place for carbon tube inside the fuselage is not aligned with the fuselage and the right is lower than left and anyway it's also too large for the carbon rod, there is a lot of play. wings won't be solid with the fuselage.



There are no air scoops for motor/esc ventilation.



Will post more once the airplane is ready and maiden.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
buen producto, plusplusplusplusplus
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
  • Target Drone

Upload video