Dimensão: 26 milímetros x 28 milímetros, 41 milímetros (com eixo)
Peso: 39 g (kv4200) (não incluindo conectores)
Diâmetro do eixo: F2.3mm
Comprimento do eixo dianteiro: F12mm
Espessura de laminação:. 2 milímetros
Tipo de magneto: 45SH
Tensão: 2-3SMax atual: 22A / 20SProp: APC4.1x4.5Thrust: 360g
Potência: 300WPara 300 tamanho helicóptero.
Características do Produto
Peso ( g )
Kv ( rpm / v )
Correntes Max (A)
Comprimento B (mm):
Pode Comprimento D (mm)
Max Tensão ( V)
Shaft A ( mm):
Unit Weight (g):
Diâmetro C ( mm )
Comprimento Total E ( mm)
Resistência (MH ):
This thing is great, I use it on my HK-250 helicopter, the only this is, I had to modify my motor mounting plate because the motor, although it came with connectors, heat shrink, and pinion gears, it didn't come with screws to mount it, so I used the screws that came with the heli, and I had to grind away some metal from the mounting plate. It was tedious work, but now it works great and I would recumbent this motor. Also the pinion gears did not mesh properly with my main gear, so make sure that they will mesh before you order it, or make sure your heli kit comes with its own pinion.tons of power for my trex 250 with a 14t pinion and flat 100pcnt throttle curve. 3min fly time on 3 cell gens ace 850 mah. For hard 3d one must use good lipo's to make the most of this motor, also motor shaft must be cut shorter to fit trex 250 - not a problem with a dremel tool, also trex 250 motor mount must be dremel'd larger for the M3 mounting bolts on motor. Motor shaft is 2.3mm and I wouldn't recommend a pinion larger than 14t for a trex 250. Just hope the motor hold up now - but so far it's really impressive when compared to the stock align motor.Super motor! Use it in Skyartec Wasp X3 with 14t pinion and YEP 18A controller.
With this motor, the Wasp X3 is better than with the original motorBought this for my blade sr with brushless tail conversion because i didnt want to spend 50 on a CC 4200kv. This seems to be a sweet little motor. Definitly more power then the stick 3900kv. Running a 1300 mah nanotech 3s 45c i think. Pinions are press on and not grub screwed like i had hoped. The sr pinion does fit so that was good.This motor will be going into a E sky Honey Bee King 2 collective pitch heli, with a 9t pinion, motor looks pretty good.Habe den Motor mit einem 11er Ritzel und dem Turnigy AE-25Amp in meinem MJX F45 verbaut, dazu noch ein 2200er LiPo mit mindestens 20C und der Heli ist kaum wieder zu erkennen und hat nun auch genug Kraft um ihn bei etwas Wind zu fliegen.Nice motor, although ended up in the bin- contrary to other reviews this won't fit an hk250 without work- the pinion in the heli kit is a 2.5mm, this one is a 2.3. The pinions included with the motor also don't have the correct tooth pitch to mate to the 250 main gear without squealing and chewing them up, and the main shaft is too long, needing to be cut down. Only found out after pressing the pinion on, so ruined the motor. Nice in bench testing though, but not for a 250.Bonjour,
J'ai command ce moteur mais je n'ai pas reu l'embout pour fixer l'hlice ainsi que le plat en alu pour fixer le moteur comme indiqu sur la photo, j'ai juste le moteur et les connecteurs.
Est-ce normal?Great speed controller,but soft start is not good.Would have been nice to have had the motor mount and prop mount included!! I did get a couple of random pinions...but am going to have to make my own mount. I guess I should not always expect to get what is shown when ordering from HK...but the price sure is nice. Hopefully the motor runs as good as it looks!