Se você é sério sobre o desempenho do seu multi-rotor, não procure mais, este motor mult-rotor Turnigy. Construído com high-end ímãs 45SH, uma alta contagem de pólo, montagem de motor personalizado e fios extra longos, este motor é projetado exclusivamente para aplicações multi-rotor.
Este motor inclui um adaptador prop estilo pinça para uso com muitos adereços diferentes do estilo que caracteriza um eixo de 5 mm. Ele também inclui um bolt-on cruz de montagem para instalação rápida e fácil em seu quadro Quadrotor.
Este não é um avião outrunner modificado. Ele foi projetado a partir do zero especificamente para aplicações multi-rotor.
Kv: 620rpm / v
Pode tamanho: 50mm
Shaft: 3,17 milímetros (inclui adaptador para montagem prop prop 5mm)
Motor Mount Buracos: 16mm / 19 milímetros
ESC sugerida: 35A
Classificado Watts: 290W
Peso: 103 g
Contagem de células: 3 ~ 4S Lipoly
Motor comprimento do fio: 390 milímetros
Características do Produto
Peso ( g )
Kv ( rpm / v )
Unit Weight (g)
Correntes Max (A):
Resistência (MH ):
Max Tensão ( V)
Shaft A ( mm):
Comprimento B (mm):
Diâmetro C ( mm )
Pode Comprimento D (mm)
Comprimento Total E ( mm):
My review keeps getting deleted!!!!! My quad crashed cause a prop shaft set screw came loose. These would be great if they came with a prop adapter that takes advantage of the holes in the bell housing. The taper prop adapter relies too much on the prop shaft being tight and they come loose on this motor.I had a review but it was deleted, I got 4 of these and in flight one of the shafts came loose, I know this because it was on the ground happening first i tightened the set screw and thought it was fine but in flight it failed and resulted in a bad crash. I got lucky and all that was destroyed was a few motors and my battery lit up. I was able to get to it fast enough to get the battery away from it before it ruined the rx and DJI naza. This motor would be perfect if they had a prop adapter that used the screw holes that are already in the bell housing, that taper prop adapter isn't good cause the shaft set screws come loose. Be aware of this.These motors are good. value for money i am very happy, I am useing them on DJI USC 30AMP opto on 680mm Carbone fiber Multicopter with Eagle three osd,Gopro Camera and Fat shark fpv. I am useing Zippy Battery 4S 5000map,highly recommended.
CossiIm using 4 of these on a FPVpilot 6061 FPV quad frame. Using 12x6 props pulling 20 amps at hover with copter weight at 3.8lbs fully loaded up with complete FPV OSD, GPS, Logger, etc...and second Gopro camera on-board. Awesome power! 15-17 minute flights with 4s 30c 5000mah lipo and 22-23 minutes with 4s 30c 8000mah lipo. Out of the 4 motors two had stripped allen screws that lock down the main shaft. When I first went to lift off 2 motors where spinning but the props where barley moving is how I found the issue...I purchased longer allen screws (2m) so I could get better thread bite. Just check these motors before flight...if you can spin the prop mounted to prop adapter on the shaft by hand while holding the motor bell then you must tighten main shaft allen screw or it might need to be replaced if stripped from the factory like mine was. Other then that these are good motors.Pretty decent motor, I have 4 of these, it appears maybe these are from a second batch as I didn't seem to find any of the wiring issues. So far, they've had about 4 hrs flight time on 4S with Plush 30A ESC. The Mrs. braided the motor wires so I had a shorter length plus my attempt to avoiding EMI issues and an overall cleaner appearance on X666 quad frame. Currently using 12X4.5 and have managed hover at about 40pcnt throttle so I'm happy for now but still very watchful. Two props were damaged during an initial test flight (pilot error), props didn't survive, but both shafts seem to have survived despite being long. I must say that I don't like the shaft that I got but from my understanding later lots of these motors now have the shorter shaft so that is a major plus for those of you who are buying these now. I made sure all grub screws were tight on these, turned out ok. Use M3 bolts to mount these and I checked to bell and to my surprise, the magnets are keyed in this can only be a good thing, and the winding is decent. I do love the finish on these, they look mean and I like sharp shiny things and they look the part on the X666. At the least a good motor to mess around with. No Wattmeter tests as of yet because I haven't had a chance to use my HK010 which came with XT60 plugs and I got lazy on buying the proper adapters to HXT 4MM hehe...*insert sheepish grin here*my review has been deleted!!wonder why??as i say,the long wires has a bad connection bad soldering job!!the wires was loose of 2 motors and in mid air another motor gave up resulting a major crash destroying 4 motors!!so before installation check the wires and maybe re soldering them!!and the shaft is to long so it bend really easy!!I bought 6 of these for a bigger multi camera platform. Paired them with the 25A hexfets, 10x5 slowfly props, a megapirates control board(Crius). 600mm center to center with a 20mm vertical staggered offset from motor to motor (future bigger props....maybe). The bells show some machine bitemarks. The bells seems well balanced and the bearings nice and quiet. Around 6min flight time on a 4000mah 4cell zippy. It has huge lifting power. They run nice and cool. Heats up the 25A ESC though. Should have gone with the suggested 30 or even a 40A. The longer motor cables are great. I mounted my ESC's in the main body. Nice and neat. I love these, thanks HK. Good value for money. Warning-since the bell is quite heavy, it generates a lot of momentum. Avoid a prop strike. It will not be pretty.Specifications:
Idle Current: 0.8A
Can size: 50mm
Can Length: 11mm
Shaft: 3.17mm (Includes Prop saver mount for GWS style props)
Suggested ESC: 30A
Best Efficiency Rated Watts : 180W
Operation Voltage: 3 ~ 5S Li-Po
We recommand to use 4s battery pack with APC 14x4.7 inch Push & Pull props.
Same setting but different motor (530KV and 620KV), we feel the 530KV is bit efficiency but 620KV is more powerful.
Take off weight: 3.5kg (Payload 2Kg)
Battery: 4000mAh 4S
Flight time: over 5min.