grande potência para o seu grande escala plano 3D.
Bom para planos de 60inch em formato 3D, 80inch para o esporte / warbird ou até 100inch envergadura para o instrutor tipo aviões slow-mosca.
Excelente eficiência e rock sólido desempenho!
Tensão de entrada: max. 37V (10S Li-po)
Kv: 280 rpm / V dentro de 10%
No. do turno: 16 Delta
Max. atual eficiência: 50A
Capacidade de corrente: 65A / 60s
Resistência interna: 28 Mohm
Sem carga atual @ 7V: 2.16A
Dimensões: 82 milímetros X 63 milímetros
Diâmetro do eixo: 10mm / 0.39in
Peso com cabos: 640g / 22,58 oz
Quantidade de pólos / ímãs: 14
Peso modelo recomendado: 5000 ~ 10000g / 176 ~ 352 onças
Equivalente Potência: brilho motor ,90-150
Estator Tamanho: 52-30
Características do Produto
Peso ( g )
Kv ( rpm / v )
Unit Weight (g)
Correntes Max (A):
Resistência (MH ):
Max Tensão ( V)
Shaft A ( mm):
Comprimento B (mm):
Diâmetro C ( mm )
Pode Comprimento D (mm)
Comprimento Total E ( mm):
There's no stock since november, does anyone know when stock arrive for this motor ? I need 2 motors to build an electric montain board.
see yafly this motor in a 2,4m an-2, with yeti spinn 99 on 8s 4000 turnigy with a 20x10 apc-e, weight complete 9,4kg. later i will try a 4 blade 18" varioprop for a better scale look. im sure you cant get more qualitiy for this money
i m verry happy with this combo, works well without any problems.
www.mac-fly.euVery good engine! I use it for 1,8m CMPro Marathon 24. I have done about 50 flights. I broke a few propellers (bad landings) but engine is still working very well!!! I don't recommend rear mounting (after firewall) - bad vibrations!!! Front mounting (in front of firewall) works very well.
My setup is:
8S5000 mAh 25C Turnigy lipo
100A HV Sentilon Turnigy
18x10 (19x10) TGS Sport propeller
About 1,6-1,8 kW!!!
You can see it at: http://www.youtube.com/user/mariuszmariusz121?gl=PL&hl=plConstruction of this motor is very solid. This motor is so nice looking you will want to tuck it in at night! Here is my setup:
Sentillion 100A HV ESC - I really like this ESC (so far) for a few minutes run time and full throttle for a few seconds it barely gets warm.
Turnigy 2200mah 3s 20C batteries - I bought 9 of these. Wired 3 sets of 3 in series. 1 set = 9s 2200mah, 2 sets = 9s2p 4400mah, 3 sets = 9s3p 6600mah. I can mix and match these batteries however I want now. When I am not flying my big plane I can use these batteries in my smaller planes.
Turnigy 5a sbec (8-40v) - You need to buy a separate bec with the Sentillion ESC. This one works great.
TGS Sport 18x8E Precision propeller - I bought a couple of these because they were so cheap. Under $4 a piece. Nice prop.
9s1p - 1800 watts
9s2p - 2050 watts
9s3p - 2350 watts (I figure about 20lbs of thrust)
This setup seems to suit this motor very well. Motor and ESC do not get too warm. This should fly my 1/4 scale super cub very nicely with power to spare!Bought one and installed on an Ultimate 90 conversion so far so good on 8s 4000mah with a 20 x 8 APC prop. Measured on a Watts meter it hits WOT @ 64.10 Amps peak and 1842.2 watts peak. The 4 stars is because they dont list the max watts :0( Hope it holds upTRES BON MOTEUR RAPPORT QUALITE-PRIX
MONTE SUR UN JODEL GRAUPNER DE 2.20M AVEC 2 X 5S-5000 25C TURNIGY
HELICE GRAUPNER 20X10 ET CONTROLEUR 100A SENTILON, PUISSANCE EXTRA POUR TIRER UN PLANEUR DE 8KG.
CHAUFFE NORMALEMENT QUAND ON TIRE DEDANS.
Stats with 100 amp Sentillon ESC, 18 x 10 prop and 2 5C 5000 lipos.
At 25 amps, 880 watts, at 60 amps, 1950 watts. More than enough to fly a 1/4 scale, 16 lb Piper Cub like aircraft.Nov 1 2010
Amazing motor Turnigy 65-64 one of the best Ive used. Powering a 78" WS Lancair 120 8s 4000Mah nano batt using a 16x10 APC propI use this motor on my Seagull Super Decathlon .120, it pull 5kg with 8s and 17x8 FIALA wood propeller, the plane weight is 6kg.
about 10 minutes of classical aerobatic fly
http://www.rcgroups.com/forums/showthread.php?t=1331818#post16439610It would be a 5 star, but my engine come with the "lenght B" out of specs because the bearing was not in the correct place. I had to open the engine and with a proper device, put it in place. After that, the dimension come to normal, and I powered it up. Happy with the product, but dissapointed with quality control. Still recomend the engine.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!