Turnigy introduzir o Min Poder Distribuidor UBEC adequado para 30cc, mais gás modelos movidos.
Esta unidade tem grandes recursos, que incluem: entrada de bateria duplo, 5v isolado linear RX BEC, 30 Amp tensão ajustável UBEC em todos os canais de saída, 8 canais de entrada de RX com saídas duplas em cada canal - simplificar superfícies de controle dupla servo.
Grandes inclusões são o regulador 5V linear independente fornecendo uma fonte de alimentação separada para o receptor, opticamente isolada poder CDI & incorporado matança de ignição remota. fontes de energia receptor, Servo & CDI estão completamente isolados uns dos outros.
Este é o primeiro sistema Distribuidora de Energia a segurança ninho o receptor dentro da distribuição de energia 'block' encurtando assim lances de cabos, acrescentando proteção para o seu toda receptor importante e acelerando o tempo de configuração.
• 5v Linear RX BEC
• 30 Amp Servo UBEC
• Os usuários de tensão UBEC ajustável
• 8 canais de entrada (um CDI de corte)
• 16 canais de saída
• LEDs de verificação 5 Estado
• bandeja receptor acolchoado e Seguro de montagem
• CDI alimentação isolada
• CDI controle de ignição remota (corte remoto)
• CDI luz indicadora de status de energia
terminal de saída de energia • CDI
• LED CDI monitor de tensão
Opcional: Indicação da tensão de entrada / saída com interruptor de alimentação externa
Canais de entrada: 8 (+1 CDI cortados)
Canais de saída: 16
Tensão de entrada: 7-13V
Servo UBEC atual: 30A (40Amp Burst)
Tensão de saída: 4.8-9.7V (usuário ajustável; padrão é 5.2V)
Poder RX: bec linear 5v
Temperatura de trabalho: - 20 a 85 graus C
Peso: 80 g
Dimensões: 116 milímetros x 88 milímetros x 13 milímetros
Características do Produto
Peso ( g )
Top, fr den Preis unschlagbar !!! Betreibe eine 3m Bella damit vllig Problemlos. Spannung einstellbar, Zndung ber die Weiche ein und ausschaltbar mehr geht nicht TOP !!!
Warte das sie wieder kommt, brauche noch 2 Stck davon....
Bitte HK schnell wieder auffllen !!! :-)IT has not LCD SCREEN. IT HAS FAKE SCREEN. There is a Turnigy writing on the fake screen. Also a led is shining back side of the fake LCD. Another functions are ok. You can buy another version of this power distributor that it has almost the same functions from another stores cheaper than hobbyking.Seemed to be a great product, all worked as it should initially, after three flights, CDI kill switch stopped working, red light flashes indicating less than 4.2V input no matter what battery is connected and the switch is inoperable.
Fitted on a Yak52 with a RCG 26cc gas engine.
I will now have to purchase a CDI kill switch.Be careful to isolate this board from vibrations on the larger planes. My opto for the ignition control came loose from the board in my Sbach 34pcnt, 35cc, because I had the screws down too tight on the rubber grommet mounts. Bad solder joint. The ignition randomly shuts off (sometimes while in flight!). I'm going to isolate the board and receiver in foam and use Velcro to hold it in the plane. JohnnyBI have purchased 3 of the original 3 panel design panel units. I have installed them into 3 of my giant scale planes. The new panels are a single plastic box. They are easy to use and they performed as intended.
CAUTION!! One of the 3 panel design units failed and I lost all power on my 84 P-51. What I found was one of the 2 ribbon solder joints fail on the main BEC that is located on the bottom panel failed. I was able to repair the remaining units by removing the top 2 panels and repairing the ribbon solder joints. Make sure to get the solder to flow to both sides of the panel. It was a simple repair but why should we have to repair them to ensure we dont lose our planes.
Come on Hobby King Pick up your game!!!!
PS I havent used the new design yet but I do hope they have resolved the problems.
This Bower box works Beautifully, But always remember to leave your assigned kill switch down when you turn on your transmitter and do this before powering up your Power Distributor, Then turn on the power distributor and your kill position will always be down to kill the CDI, This sequence is necessary unless you don't care where the kill position will be. This is a built in Safety feature to always start with the system in the kill position. Hope I made it clear to avoid confusion. Happy Flying ! RonGreat product awesome price for this product. Only one thing could be made better.... an voltage display fr the bec adustment or an DIP Switch with steps and not an potentionmeter...
But again an awesome Product.Muy buen producto... pero no es de 30AVoltage to the servo will not change with the screw adjustment. It's stay the same as the default voltage 5.2 V.I have it installed in my Raven, this thing works as advertised, the Opto Kill swiitch works really well. Just one little quirk, regardless of the servo direction you put the Opto Kill Switch onto, it defaults to the off position. Meaning, if you turn on the receiver regardless on the position of the switch on the transmitter, it defaults to off. Other than that little quirk, it's a great little unit. I have 2 X 2400 Mah 20C Lipo's hooked up to it, and the voltage regulator set to 6.0 volts. To adjust this, you'll need to turn in the potentiometer about 2.5 turns inwards. But the voltage is stable regardless of the state of the 3S Lipo. Receiver voltage is stable at 5:0Volts. Highly recommended.
Note, this is a rebranded RCCSKJ Power distribution board. The Yellow one is rated at 20 amps with peak of 30, that's a whole lot of amps for any size plane.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
Diode Schematic bt JohnnyB download now [12kb] Schematic by JohnnyB download now [12kb] Instructions download now [107kb] Exploded download now [1096kb] Plastic....... download now [95kb] schematic design download now [2788kb]