New Items Forum
Registar

Total Price

0,00 €

Carrinho 0 Carrinho 0 Loading...

Turnigy Multistar 10 Amp Multi-rotor Brushless ESC 2-3S

Turnigy Multistar 10 Amp Multi-rotor Brushless ESC 2-3S

Discontinued Product

Please continue searching for a similar product.
Peso:
20 g
SKU:
9351000001
WANT FREE SHIPPING? Click here to find out more!

MultiStar CES são são um controlador de velocidade de qualidade a um preço fantástico! Projetado para instalação simples e fácil configuração dessas CES têm provado para oferecer excelente desempenho quando usado em aplicações multi-rotor. Se o seu começando no Multi-rotores e precisa de um fácil de instalar solução que é testada e comprovada para o trabalho com artesanato Multi-rotor, em seguida, estes controladores de velocidade tem coberto.

Estes ESC caracteriza uma resposta do acelerador linear ainda muito lisa, sem sacrificar um rápido, batata frita, resposta a qualquer entrada do acelerador. A segurança não é esquecido com a bateria de todos Multistar Esc com ajustável LVC (set tipo de bateria para Lixx desativar LVC), protecção do motor parado (sobrecarga), sinal de perda de shut-down e armar seguro.

Todas as séries Multistar ESC veio com conectores de bala instalados que são adequados para manipulação de potência nominal do ESC. Isto permite plug and play conveniência simplesmente adicionando o divisor apropriado de alimentação da bateria (3,4 ou 6 ESC) e extensões de cabo do motor a partir da linha de acessórios modular Multistar. O que poderia ser mais simples?

recurso de todos os Multistar ESC um MCU ATmega que abre a porta para firmware customizáveis ​​- para aqueles tão inclinado! ou, alternativamente, um cartão de programação pode ser usado com o software instalado para configuração rápida e fácil com o software pré-brilharam.

Por favor, consulte os itens relacionados abaixo para uma solução de energia multi-rotor livre de solda de acordo com seu projeto multi-rotor seguinte.

Características:
• controle suave e acelerador linear
• Resposta rápida para a entrada do acelerador
• MCU Atmel
• proteção do motor de estábulo
• sinal de aceleração perdem a protecção
• (bloqueio do acelerador) power-on Seguro
• Suporte 480Hz + taxas de actualização elevadas (até 499hz)
• Compatível com cartão de programação

especificações:
Constante atual: 10A
Tensão de entrada: 2-3 células Lipoly
BEC: Sim (linear) [Remova o fio do meio para dissable]
BEC saída: 5V / 2A
PWM: 8 KHz
Max RPM: 240,000rpm para 2 Pole Brushless
PCB Tamanho: 22 milímetros x 17 milímetros
Descarga Plugs: Masculino 2 milímetros bala Connector
Motor Plugs: 2 milímetros Feminino Bala Connector
Peso: 16 g

Manual já está disponível para download na aba "Arquivos".

  • SKU 9351000001
  • Brand -
  • Capacidade ( mAh) -
  • Peso ( g ) 20.00
  • Comprimento 110.00
  • Largura 10.00
  • Altura 100.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

So tiny and lightweight and perfect! Already ready to go with 2mm connectors on all the wires. At this price its a no brainer.. Perfect for my 250!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

So tiny and lightweight and perfect! Already ready to go with 2mm connectors on all the wires. At this price its a no brainer.. Perfect for my 250!

Don't bother with these they don't perform well at all. and can not be flashed with socket tool as atmega chip is to small very small. wast of money get some Simon k instead I'm very disappointed with these want my money back their useless for multi rotors!!!!!!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Don't bother with these they don't perform well at all. and can not be flashed with socket tool as atmega chip is to small very small. wast of money get some Simon k instead I'm very disappointed with these want my money back their useless for multi rotors!!!!!!

Mis avec turnigy multistar 1704 pas de surchauffe bon vario

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Mis avec turnigy multistar 1704 pas de surchauffe bon vario

Bought these for my 250 mini quad with multistar 1704 motors and mini APM flight controller. I did also got the program card and set them up best i can. Even on NIxx on lowest setting my battery alarm goes off and they are already cutting the power to the motors. I am gonna try the HK f10a flashed with simonk next as these will eventually lead to a bad crash. Also the overload cut off is annoying because if you touch back down one or more motors will quit and you have to disarm and rearm. I am not sure why they engineered these the way they did since basically they are not good for multirotors at all??

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Bought these for my 250 mini quad with multistar 1704 motors and mini APM flight controller. I did also got the program card and set them up best i can. Even on NIxx on lowest setting my battery alarm goes off and they are already cutting the power to the motors. I am gonna try the HK f10a flashed with simonk next as these will eventually lead to a bad crash. Also the overload cut off is annoying because if you touch back down one or more motors will quit and you have to disarm and rearm. I am not sure why they engineered these the way they did since basically they are not good for multirotors at all??

Good esc(s) placed in my 330 frame with a KK2.1 board flashed with 1.11 firmware, 3s 1000mah Zippy compact batt, Turnigy 10amp Multistar esc(s) 8ch 9x receiver, power board soldered the esc direct to it and XT60 batt plug on it, 8045 props, this thing it a rocket and getting 6 minutes flight time. After flight everything is cool. Will hoover with only 40pcnt throttle. Motors are Turnigy D2822/17 1100 kv. I did soldered 3.5 bullet ends on everything.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good esc(s) placed in my 330 frame with a KK2.1 board flashed with 1.11 firmware, 3s 1000mah Zippy compact batt, Turnigy 10amp Multistar esc(s) 8ch 9x receiver, power board soldered the esc direct to it and XT60 batt plug on it, 8045 props, this thing it a rocket and getting 6 minutes flight time. After flight everything is cool. Will hoover with only 40pcnt throttle. Motors are Turnigy D2822/17 1100 kv. I did soldered 3.5 bullet ends on everything.

No better than any non flashed esc for multirotors, after flashing with simonk they are 10x better, but this is not easy as there are no pads and the hk flashing tool is too big for the atmega chip on this esc, so you have to solder directly to the chips pin outs. For this reason I would not buy anymore as there are others available that are far easier to flash. If they are specifically for multirotors why does it have brake settings, set to medium as default lol.

They also have no throttle calibration, they are auto like dji escs, but you get throttle calibration when flashed.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

No better than any non flashed esc for multirotors, after flashing with simonk they are 10x better, but this is not easy as there are no pads and the hk flashing tool is too big for the atmega chip on this esc, so you have to solder directly to the chips pin outs. For this reason I would not buy anymore as there are others available that are far easier to flash. If they are specifically for multirotors why does it have brake settings, set to medium as default lol.

They also have no throttle calibration, they are auto like dji escs, but you get throttle calibration when flashed.

i've got a few brands of 10amps this is the one which fits me the best especially compared to the piece of crap red brick also from here...

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

i've got a few brands of 10amps this is the one which fits me the best especially compared to the piece of crap red brick also from here...

Really cool ESC for mini quadcopter. I use them with Turnigy Multistar 1704-1900K, kk2.1. And works well. I calibrated them straight kk board.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Really cool ESC for mini quadcopter. I use them with Turnigy Multistar 1704-1900K, kk2.1. And works well. I calibrated them straight kk board.

nice little ESC. Runs without flashing to SimonK also good enough for smaller Multicopter.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

nice little ESC. Runs without flashing to SimonK also good enough for smaller Multicopter.

Works ok, but gets hot faster than eg. the tgy plush esc. Bought a bunch for a small quad and put another on a bonsai flying wing. Dont forget to get the programming card too!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works ok, but gets hot faster than eg. the tgy plush esc. Bought a bunch for a small quad and put another on a bonsai flying wing. Dont forget to get the programming card too!

  1. 1
  2. 2
  3. 3
Customer files
Manual - Turnigy Multistar Brushless ESC Download [2384]
Multistar 10A SimonK 1 Download [115]
No File Name Download [94]
Turnigy Multistar ESC Manual Download [2384]
No File Name Download [214]
Multistar 10A flashed with simonk 1 Download [819]
Multistar 10A flashed with simonk 3 Download [3348]
Multistar10A-1 Download [229]
Multistar10A-2 Download [167]
Turnigy ESC All Download [2298]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save