Registar

Product Finder

Definições

Useful links

Bate-papo ao vivo
 
[["US","AU","GB","DE"]]
Registar

Turnigy Multistar 20A V2 Magro BLHeli Multi-Rotor sem escova ESC 2-6S

Turnigy Multistar 20A V2 Magro BLHeli Multi-Rotor sem escova ESC 2-6S

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Peso:
30 g
SKU:
9351000061-0

Combine

essential items and
motor
acc
Descrição
do

MultiStar CES é um controlador de velocidade de qualidade a um preço fantástico! Projetado para instalação simples e fácil configuração dessas CES têm provado para oferecer excelente desempenho quando usado em aplicações multi-rotor. Se você está começando no Multi-rotores e precisa de um fácil de instalar solução que é testada e comprovada para o trabalho com artesanato Multi-rotor, em seguida, estes controladores de velocidade tem coberto.

As feições de estes V2 ESC software BLHeli para uma resposta do acelerador linear ainda muito lisa, sem sacrificar um rápido, batata frita, resposta a qualquer entrada do acelerador.

Todas as séries Multistar ESC veio com conectores de bala instalados que são adequados para manipulação de potência nominal do ESC. Isto permite plug and play conveniência simplesmente adicionando o divisor apropriado de alimentação da bateria (3,4 ou 6 ESC) e extensões de cabo do motor a partir da linha de acessórios modular Multistar. O que poderia ser mais simples?

recurso de todos os Multistar ESC um ATmega MCU que abre a porta para cu firmware - A V2 Multistar vem com software BLheli pré-instalado, e para aqueles tão inclinado a facilidade de usar a ferramenta USB está disponível para configuração e atualização através do BLHeli Suíte GUI.

Por favor, consulte os itens relacionados abaixo para uma solução de energia multi-rotor livre de solda de acordo com seu projeto multi-rotor seguinte.

Características:
• Software BLHeli
• actualização ferramenta USB e configuração via software BLHeli GUI
• controle suave e acelerador linear
• Design fino para fácil instalação quadro
• Resposta rápida para a entrada do acelerador
• MCU Atmel
• proteção do motor de estábulo
• sinal de aceleração perdem a protecção
• (bloqueio do acelerador) power-on Seguro
• Suporte 480Hz + taxas de actualização elevadas (até 499hz)
• Suporta OneShot125

especificações:
Constante atual: 20A
Tensão de entrada: 2-6 células Lipoly
BEC: Sim (linear) [Remova o fio do meio para desativar]
BEC saída: 5V / 3A
PWM: 8 KHz
Max RPM: 240,000rpm para 2 Pole Brushless
PCB Tamanho: 62 mm x 13 milímetros
Descarga Plugs: Masculino três milímetros bala Connector
Motor Plugs: 3mm Feminino Bala Connector
Peso: 20,3 g

Product
Specifications

Características do Produto

  • SKU:
    9351000061-0
  • Brand:
    MultiStar
  • Peso ( g )
    30.00
  • Comprimento
    90.00
  • Largura:
    10.00
  • Altura:
    15.00
Community
Discussions
Rate&
Review

Escreva a sua análise

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
GREAT DEAL, WORK SUPER WELL AND ARE PERFECT SIZE FOR MY QUADCOPTER ARMS
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Awesome little ESC. I use them on Flite Test airplanes, they are nice and light and the BEC works awesome. On the long side, but being so light outweighs that.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I use 4of these in my Hercules quadcopter with 2216 motors and 4s battery, mounted inside the arms.
They work perfectly and stay nearly cold. I will order some more of them for my next project.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I use 4 of them on a quadcopter, conncted through an APM and they work perfectly. However I have 2 more not working on a plane, connected to an Assan 2.4GHz V2 receiver (MPX Tx and Assan universal TxModule). They work using a servo tester but not on the receiver (nothing happens, like there is no signal). The Rx works OK with any other brand of ESC, so it is really a problem with the Multistar ESC.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I just bought 4 of these, 3 worked 1 failed. I have purchased many mulitstar esc's and have them on many of my multirotors. Till now I have been very pleased with this brand. I will continue to buy them because of price and performance, but there is a quality issue that needs to be addressed. In failing I mean the motor would not start, it tried for about 2 sec each time I initiated the mulitirotor, so I swapped motors because this was a brand new esc which didn't work so I switched to a plush esc and both motors tried will now work.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
cute little esc, still not small enough for trifecta tail tray, nonetheless the quality is good and it has bootloader so much easier to change firmware than stock esc which needs soldering or flashing tool.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
no frail ESC, slim built is easy to install between arms.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Ordered these to fit inside 16mm arms (15mm inside), they fit perfectly.
Sadly the quality control is low, I ordered in total 5 Opto's and 3 with the BEC for my Hexa, and found 1 Opto and 1 with BEC to be faulty out the box. Strange issue with on as it was acting differently to the others and the other one just did not work out the box.
I'm not sure if this is relevant, but the two faulty ones I ordered about 3 weeks before the 6 working ones, i wanted to test them but they got stuck in the post so I ordered the 6 I needed. Maybe the new batch is now better?
Anyway, I had 6 working so I'm using them with MultiStar Elite 3508-268kv motors with 17x5.5 props and a 960 Hexa.
Upgraded firmware to BLHeli v14 and altered some settings to get my best results.
Closed Loop MUST be OFF as with Low Voltage Limiter.
Motor Gain at 1, the same with Startup Power.
Temp protection off, PWM Dither 7 and Low RPM Power Protect On.
Demag MUST be OFF.
For best results PWM Frequency / Damped MUST be set to "DAMPED LIGHT"
Motor Timing is best at Medium, Low pulls more power!.
Anything noted as MUST caused the motor to run slower or react to throttle changes strangely or slowly. Others were decided by current draw or best feel.
Any settings not included here either where not available in v14 or seemed unimportant.
Kev
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This ESC working good with multistar 2216 motor and 4s battery.
Except one serious issue: here is how to reproduce it
1. connect the battery and wait for 10 min
2. after 10 minutes, your esc should begin to beep, then wait another 3 minutes
3. disconnect and reconnect your battery really fast

Then you have a very high chance to burn both your esc and your motor. I have burn two esc and two motor in the same way.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
great ESC... very small for tube install... configuration -> no problem with BLHeli Tool... flashing software is not necessary to use them... very low heat generation... exactly that i missed...
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!

Combine

essential items and
motor
acc

Etiquetas de Produtos

Utilize um espaço para separar as etiquetas. Utilize aspas simples (') para frases.