Turnigy 1266HV Digital Titanium Engrenagem Servo 57g / 11 kg / .08sec - servo cíclica Perfeito para 50 e 90 de tamanho Heli.
Tensão de funcionamento: 6.0V / 7.4V
Corrente de funcionamento: 300mA / 400mA
Velocidade de operação: 0.10sec.60º / 0.08sec.60º
Stall Torque: 9kg.cm /11kg.cm
Peso: 57 g
Banda morta: ≤2uSec
Motor: Tipo de Coreless
Rolamento de esferas: 2BB
Caixa de velocidades: Titanium
Fio conector: 300 milímetros
Ligue: JR Tipo
Faixa de temperatura operacional: -20 ° C + 60c
Características do Produto
Peso ( g )
Speed ( Sec / 60deg )
Torque ( kg) ( min. 0,01 kg )
Unit Weight (g):
A ( mm ):
C ( mm )
D ( mm ):
E ( mm):
F ( mm )
I PURCHASED 3 OF THESE FROM HK ,THEY ARE WELL MADE ,THEY CENTRE PERFECTLY, AND ARE SMOOTH ,THE TORQUE IS 9.3LBS OR 150OZS ON 1 INCH ARM AT 6 VOLTS, WHICH IS ABOVE SPEC.I THINK THEY ARE THE SAME AS POWER HD 8309s . THEY ARE MADE IN TAIWAN ,WHICH USUALLY MEANS GOOD QUALITY. THANKS HK.Very impressed with these servos. Have opened up to lubricate the gears as they are a bit under lubricated. They are very nicely made with very positive and smooth movement, very fast accurate to centre and relatively powerful. Good value for the money. They appear to be from Power HD. I expect good service from themVery good servo for the price!!!
I use it on TEKNO SCT410, and its great.
The possibility to use both 6V and 7V currents is very nice...Fantastische servo,doet wat er vermeld staatBought 4. One feels like it's full of sand. The splines are 1 mm bigger than the other futaba servos I have. Very tight to get the arm on. Can't put them on by hand have to screw them in.Running this bad boy in my drifter! Only have 6V going to it, and it's great. Much faster than I expected :) have bought another Turnigy servo for my 4x4 SCT I'm building which is also going to be running a turnigy ESC & Motor! Should be interesting to see how it goes @ such a low build price $$$.Sehr schneller Servo! Verbaut in einem 1:8er Buggy. Seit 2 Monaten im Einsatz und null Probleme damit. Kann man weietrempfehlen!This servo is 1520 us and max 333mHz This from the HK suport staff. Have them on a TZ 50 flybarless. after short first test had tail wag so it maybee not fast inought on tail. have the HK Mi hv 0,03sec in order for the tail.though servo... works perfect for cyclic on 550, altough i need spacers approx 2 mm for the ailerons... very good servo, really fast. connected to djt hv receiever with direct zippy lipo 45c, is a real powerhouse with great centering, time will tell how much will they last... havent flown it yet, but i think that they will do the job as I expect... so far so goodAfter over 200 flights... Those servos survived 2 crashes! Today failure of one servo during landing. I was lucky to land and did not crash. Gears are ok, one wire going to potentiometer lost contact (bad soldering or due to vibrations). After I soldered that wire servo works fine.
Those are good servos. If you fly expensive model it is easy to check those wires for safety reasons.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!