Este barco estilo de corrida clássico é construído a partir de madeira compensada laminada e bem acabado. Ele tem dois painéis de escotilha removíveis que facilitam o acesso electrónica e trocar baterias uma brisa. Ele também possui peso leve, extremamente rígidas de fibra de carbono suportes sponson de boom.
Este barco é em forma de kit, o que significa que você precisará adicionar seu próprio hardware, como o leme, eixo da hélice / mount, hélice e eletrônica.
* Nota: Acima de fotos de modelo montados são apenas para referência. Esta versão terá de ser montado e chega em forma de embalagem plana, como mostrado na última foto. Para a versão pré-montada, consulte itens relacionados abaixo.
Eixo da hélice: 3,17 milímetros
Leme: 75 milímetros
Motor: Watercooled 3700kv 28 milímetros
ESC: Watercooled 40A +
Servo: 9g x 1
Bateria: lipoly 3S 2200mAh
Sistema de Rádio: 2CH
Material do casco: laminado de madeira compensada
Casco Comprimento: 495 milímetros
Largura: 380 milímetros
Altura: 60 milímetros
Casco Peso: 230g
Características do Produto
Peso ( g )
kit arrived with missing laser cut board! In process for RMA but I dont thing HK will sent only the missing part! I will have to sent back the item to HB!! less trouble to buy wood and make that missing part!My kit arrived with missing laser cut board,tried for several weeks to have this resolved with hobbyking,but had to use paypal for refund,cannot build boat so gave up.Just my own opinion but the kit I received on looks seemed to be a very average cut kit there were burn marks all over the ply. the actual kit goes together very nicely but I would recommend a few things. The ply has been badly laminated enough that some of the parts are very weak (top section and covers)
First and foremost throw out the carbon tubing it is of very low quality put steel or brass tubes in that protrude slightly from the sponsons and main hull and use carbon rod that fits into the tubing use small clips to hold it in.
do not use CA glue to put a ply kit together use a pva and seal with a good epoxy resin.
I wont go into the hardware selection just yet but I will do a build diary on the forum when im done
Well upon opening the box I was very impressed with cut quality and overall quality of the plywood. Some of the laser work needed an xacto to pop free though, but fit and finish seems to be dead on. Ill post another review once I finish the build with all my hardware used and tuning tips.nice kit
fun to build and very simple to build
i will keep you posted to how it goes and what i end up running in the boat in the way of hard wear
i will buy another kit as a 2nd boatHey Hobby King, we want a STRUT for this hull. Nobody can do much with all these hulls without the hardware!
2mm ply except tub sides which are 2.3mm. The design is heavy. No foam cores for the sponsons. Sponsons are permanently attached with current design. Design will make it difficult to make sponsons removable. Holes already in transom- bad thing when you cant get the right strut!
I would like to build 3-4 of these in total to encourage others to boat in my area.
Somente usuários registrados podem fazer o upload de arquivos. Por favor Registre-se para que você possa começar a ajudar seus colegas de hobby hoje ainda!Customer files
ÐœÐ¾Ñ Ð“Ð˜Ð”Ð Ð download now [5640kb] Ð’Ð¸Ð´ ÑÐ¿ÐµÑ€ÐµÐ´Ð¸ download now [5603kb] Strut dims 2 download now [60kb] The build1 download now [98kb] transom setup1 download now [107kb] transom setup2 download now [116kb] tub setup1 download now [106kb] fresh paint1 download now [1365kb] fresh paint2 download now [1340kb] fresh paint3 download now [896kb] in action download now [559kb] Homemade boat plans download now [746kb] Homemade boat plans2 download now [773kb] homemade version download now [106kb] The bow download now [71kb] Homemade version2 download now [2131kb] Another ply project download now [1990kb] Finished hull download now [456kb]