Зарегистрируйтесь

Product Finder

Настройки

Useful links

Живой чат
 
[["US","AU","GB","DE"]]
Зарегистрируйтесь

5W синий светодиодный сплав Газа 150 мм х 12 мм (3s-совместимый)

5W синий светодиодный сплав Газа 150 мм х 12 мм (3s-совместимый)

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Вес:
10 g
Артикул:
371000068
Описание
товара

5W синий светодиодный сплав Газа 150 мм х 12 мм (3s-совместимый)

Технические характеристики:
Размеры: 150 х 12 мм
Вес: 8g
Разъем: JST
Угол пучка: 120 градусов
Мощность: 5w
Цветовая температура: 460-465nm
Напряжение: 11.1V-13.5V (3s LiPoly)
Ток: 300mA
Световой поток: 400-450LM
Индекс цветопередачи: 70-85
Материал: алюминиевая пластина
Срок службы: 50000 часов
Рабочая температура: -20 - +60 градусов по Цельсию

* Примечание: убедитесь , что ток ниже , чем 300мА или вы рискуете повредить светодиодные ленты
Product
Specifications

Дополнительная информация

  • Артикул:
    371000068
  • Brand:
    Нет
  • Емкость ( мАч )
    Нет
  • Вес ( г )
    10.00
  • длина:
    155.00
  • ширина:
    5.00
  • Высота
    25.00
Community
Discussions
Rate&
Review

Напишите ваш собственный отзыв

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
I run them with a Meanwell LDD-300L (http://www.meanwell.com/mw_search/ldd-l/LDD-L-SPEC.PDF) switching DC current driver to ensure the leds are driven within rating despite the battery voltage (you can run them from about 10V to 36V input voltage). They are very bright, but only heat up to about 40C. Additionally, this driver has a PWM input (up to 1Khz, not servo-PWM) which I have connected to a GPIO of my Pixhawk flight controller using a N-FET inverter (the GPIO can't drive the current neccessary for the PWM input, I've used 100 Ohm in series to the gate for protection, 100K pull down on the gate and 1K pull up to the battery voltage on the drain). Using the PX4-built-in application gpio_led, the led stripes begin to blink when the battery reaches a low voltage.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Extreme Bright ! be careful, the polarity its reversed on JST connector, you must solder a 4.7ohms/1W in series to avoid overheating. Do not look directly over short distances
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Awesome for brightness! I read some of the reviews and thought I could deal with the heat... Unfortunately it gets so hot on 3s the solder melts and the wires fall off! Too bad, because they look great. Totally unusable.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
This thing is very bright but way too hot. I'm not sure what you could put this on without damaging it. Certainly not foam it would melt it seconds. Only the red color stays cool but it has what I think is a regulator in line.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
ridiculously bright which is cool BUT COOL the lights aint, as mentioned in the other reviews they get WAY too hot and will drain a 1000mah 3S in about 2 mins..... Tried it on 2S but it barely lights up, guess will have to try a 9-10v set up but not too sure what to do, any suggestions?
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
WAY TOO HOT TO HOLD!!! would probably melt your airplane. These are super bright!! LOOKS AMAZING!!! I would like to mount 6 on my hexcopter, but they will need a WAY bigger heat sink... REALLY HOT!!!!!!! did I mention how awesome they look though?!?!?!?
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I just got this and tested it. It's super bright but it gets very hot really fast so I'm not sure how well this will hold up.
verified_user Quality
trending_up Value
playlist_add_check Overall
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Метки товара

Используйте пробелы для отделения меток. Используйте одинарные кавычки (') для фраз.