Эта скорость машины Твин Халл включает в себя два 380 двигателей для твин медной опоры установки. Вам потребуется два 70A с водяным охлаждением ЭСК, два LiPoly батареи 3000mAh 3S 20C и собственный передатчик и приемник, чтобы закончить эту модель.Эта лодка была построена для скорости и не рекомендуется для небольших прудов или неопытных водителей.СпекуляцияДлина: 800ммШирина: 240ммВысота: 120 ммВес: 4кгДвигатель: 2 х 380 2881kv Водоохлаждаемая Бесщеточный InrunnerESC: 70A с водяным охлаждением (обязательно)Необходимые.
Система радиосвязи (2ch) и приемник
1 х 3кг стандартного размера серво3300mAh 3S 20C Lipo или больше
ESC: 70A с водяным охлаждением (обязательно)* Запасные части и принадлежности, прибывающие в ближайшее время!
Вес ( г )
It Doesn't mention it but mine came with contra rotating props. Very stable, fairly quick on 3s but not mental.heres a links of it running https://www.youtube.com/watch?v=7Ku376CTdQw
JUST DID A BUILD WITH THIS BOAT USED 2X Dr Mad Thrust 2200kv 1600w 70mm EDF Inrunner 6S version (29mm) WITH 29MM WATER JACKETS AND 4MM TO 4MM SHAFT ADAPTERS 2X Hobbyking SS Boat Series 200A ESC 4X Turnigy nano-tech 4000mah 3S 35~70C Lipo Pack HobbyKing HK-GT2B 3CH 2.4GHz Transmitter and Receiver w/Rechargable Li-ion Battery Mi Digital High Torque MG Servo 6.0kg / 0.11sec / 26g SO QUICK IM SCARED TO DRIVE IT :0As the description says, this boat is fast. I fitted it out with twin 125amp ESC and 4000mah 3S batteries. I had to put a couple of bends in the rudder shaft to get the shaft under the hull structure due servo size. The finish is excellent and smooth. The instructions are limited so some experience is required to set it up properly. The use of the tape to waterproof the cover is not ideal but it did work pretty well. There was some water in the hull afterwards. To grease the prop shafts, undo the motor bolts and collet then slide the shaft out and apply the grease. Reverse procedure to refit. This boat is extremely stable at speed but do not attempt to turn quickly at speed or it will tip over. Very good value and worth it. Enjoy.JUST DID A BUILD WITH THIS BOAT
USED 2X Dr Mad Thrust 2200kv 1600w 70mm EDF Inrunner 6S version (29mm) WITH 29MM WATER JACKETS AND 4MM TO 4MM SHAFT ADAPTERS
2X Hobbyking SS Boat Series 200A ESC
4X Turnigy nano-tech 4000mah 3S 35~70C Lipo Pack
HobbyKing HK-GT2B 3CH 2.4GHz Transmitter and Receiver w/Rechargable Li-ion Battery
Mi Digital High Torque MG Servo 6.0kg / 0.11sec / 26g
SO QUICK IM SCARED TO DRIVE IT :0Note: I bought the 70amp SS HK speedies to go with each motor.
OK, so first run out I ran each motor on 2 cells (7.4v lipos) for the steering I use a spare traxxas steering servo from a Emaax since it water proof and an old 1/10th car speedie to power the servo & RX.
First thing I learned - the boat dont turn really well until you punch it and get it plainning :-) thought it very cool. After the run however - the lipo packs got thumped! They were pretty hot as were the motors, speedies not so much. Also found alittle water in the back near the booty for the servo rod - grease rod and add some extra CA to the boot where it meets the hull = no more water at all!
Next run I tried running both 2 cells in series to make 4 cells (4S 14.8v) but with in 5mins the packs got so hot one of the wires got too hot and melted the solder. :/
So checked the water flow system and it was all good, then I pulled out both motors and the drive shafts (Not that hard to work out square end to the prop shaft and collar setup to the motor), there was no grease down the flex drive - only where the square end runs in to the prop bolts. The motors felt a little... well the bearings felt a little hard, so I greased up the flex drives and put them back together and used bearing lube on each end of the motors - then put them back in.
Took it for a test with 2 x 5000mah 40~80c 3 cell lipos - one for eaGot mine and build is great has no ESC,s my motors are black,and has counter rotating props and shafts! am only running 2200ma 25-35c batteries but goes great!!taping and un-taping hatch is a bit of a pain but VERY fun to driveFantastic boat!!! great looking,runs just like the real thing and is easy to drive.I used a lot of the suggestions i found on forums and stripped the boat down first to properly lube the drives with PTFE grease,reinforced all the mounts with 2pac epoxy,thread locked all the screws and dressed and polished the props.Im using the Hk ss 70a esc's and turnigy 3S 3000 and 4000 batteries.The twin motors really give the boat that authentic look.Ive just ordered two 4500kv motors and the "blonde dynamite" decal set to put on the front topsides (just the girl) should look fantastic.Hi all, I bought this boat in November 2011 the motor stopped working in the first week . Today is 15 June 2012 and I am happy to say the motor has been replaced. I had already upgraded the motors and with 4s battery's send this thing like a bullet . Even with the extra long wait from HK customer support and replacement of the motor this boat is well worth buying, forget about getting things replaced if they break, just get a new one and get on with the fun. Hope you all enjoy:)This is a great boat! for the price it cant be touched. You will need a ESC,servo and lipos but well worth it and would recommend to anyone looking for a fun solid boat. The only thing i didn't really like was the location of the water outlet, it gets in the way of the batteries.I ment to give it no stars, a used second hand broken boat doesnt rate high on my chart, very disappointed, im shore they will expect me to pay for return post too.