Стать поставщиком Блог Новинки
Зарегистрируйтесь

Итоговая цена

0,00 A$

Корзина 0 Корзина 0 Loading...

EDF64 с C20 Motor Собранный 144W

Generating Links

EDF64 с C20 Motor Собранный 144W

Цена:

Now save сохранить 0,00 A$ 0,00 A$

35,22 A$
Уже купили Discontinued Product

Please continue searching for a similar product.
Артикул:
EDF64-C20
Хотите бесплатную доставку? кликните сюда Узнать больше!
EDF64 с C20 Motor Собранный 144W
С двигателем C20Pro, данное устройство EDF обеспечивает хороший баланс между потреблением тока и тяги.


Спекуляция
Испытательное напряжение: 11.1V (3S)
Испытательный ток: 13A
Упорный: 420г
Мощность: 144.3W
Двигатель: C20pro 3600kv
Загрузить видео

Для загрузки видео необходима регистрация войти в систему или Зарегистрируйтесь

Темы
Сортировать по
Самые последние темы
* Псевдоним пользователя:

* Ваш ответ:


Пожалуйста, введите текст, показанный на картинке, в поле ниже
*Код верификации:
Отменить
Отправить
Опубликовать новую тему
* Псевдоним пользователя:

* Ваша тема:



Пожалуйста, введите текст, показанный на картинке, в поле ниже
*Код верификации:
Опубликовать тему

Для того, чтобы оставлять отзывы, необходимо зарегистрироваться войти в систему или Зарегистрируйтесь

Клиент | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Nov 08, 2008

Muito bom, ultrapassa as minhas espectativas. Assobia nas horas!!!

Bare | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Nov 06, 2008

Just recieved Mine. Seems OK Motor bell can be pulled back approx 4mm that Definitely needs looking into. Also evidence of Fan rubbing on the Duct, motor/rotor is Not centered. Were these factory 'test run' ? Or did I get a Used 'return' unit as only running it could cause these markings.

Could be Fine.. with a rebuild, I hope. I'm also thinking I should have gotten the ADH 300 version as that motor is at least twice as long.

Клиент | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Sep 16, 2008

Yesterday I maid my first testrund in my selfmaid depron FW TA-183 "Huckebein" (Destweight 350 gr.) with a 20 Amp RX and 1000mAh 3S Lipo and what should I say "Wauh"... The model makes a lot of noise and produces a lot of thrust !

Thx Hobby City

David L | Проверенный покупатель

  • Overall
  • Quality
  • Value

Not bad, some problems

Nov 14, 2007

EDF housing appears to be a GWS or clone housing. Outrunner motor makes a nice light EDF unit.



But, I only measured 320 grams of thrust @ 13.5A, 11.1v on a Zippy-H 30-40C 2500mah, using a Turnigy 25amp ESC. Both motors gave the same thrust, so the advertised 420 seems a bit suspect (unless I got two duff motors). I wonder if they'd survive 4s...



Build quality on one motor was also very poor. The stator wasn't pushed down the bearing tube entirely, so the end of the bell was able to rub against the stator coils (and rub off insulation) when pulled forward (e.g. by the fan thrust). Fortunately I noticed this before running the motor, and was able to force the stator down the tube by gently clamping it in a bench vise between soft wood blocks.

Other motor was fine, though the set screws look easy to strip if you're not careful.

Загрузить файл

Зарегистрируйтесь, чтобы загружать файлы.
пожалуйста войти в систему или Зарегистрируйтесь Начните помогать коллегам по хобби!