Стать поставщиком Блог Новинки
Зарегистрируйтесь

Итоговая цена

0,00 A$

Корзина 0 Корзина 0 Loading...

KD KA400H 3500kv brushles Heli Motor

Generating Links

KD KA400H 3500kv brushles Heli Motor

Цена:

Now save сохранить 0,00 A$ 0,00 A$

18,20 A$
Уже купили Discontinued Product

Please continue searching for a similar product.
Артикул:
KA400H
Хотите бесплатную доставку? кликните сюда Узнать больше!

KA400H
Вал Размер: 3.17mm ~ 14mm / 2.3mm ~ 14mm (два размера вала в комплекте)
Мотор Размеры: ³28mm ~ 29мм
Вес: 43g

Спекуляция
Kv: 3500rpm / V
Батарея: 2-3cell Липо (7.4-11.1v)
Opperating ток: 8-16A
Пиковый ток: 19A

  • Kv ( об / об) 3500.00
  • Max Токи (A) 19.00
  • Сопротивление ( тк ) 0.00
  • Максимальное напряжение (В ) 11.00
  • Мощность (Вт ) 0.00
  • Вал А ( мм) 3.00
  • Длина В ( мм ) 28.00
  • Диаметр С ( мм ) 28.00
  • Может Длина D (мм ) 15.00
  • Общая длина E (мм ) 44.00
attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Загрузить видео

Для загрузки видео необходима регистрация войти в систему или Зарегистрируйтесь

Темы
Сортировать по
Самые последние темы
* Псевдоним пользователя:

* Ваш ответ:


Пожалуйста, введите текст, показанный на картинке, в поле ниже
*Код верификации:
Отменить
Отправить
Опубликовать новую тему
* Псевдоним пользователя:

* Ваша тема:



Пожалуйста, введите текст, показанный на картинке, в поле ниже
*Код верификации:
Опубликовать тему

Для того, чтобы оставлять отзывы, необходимо зарегистрироваться войти в систему или Зарегистрируйтесь

Zbigniew | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Jul 08, 2012

I've just received this motor, and it came with two 3mm shafts. Although description of this item was wrong it's OK for me, because 10T 3.17mm pinions are out of stock :-)

| Проверенный покупатель

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jul 06, 2012

Great motor, better than some of the eflite motors I have used in the past. Shaft is kind of hard to take out.

Lamborgotti | Проверенный покупатель

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jun 15, 2012

very powerfull motor not only for heli. use it in a fixed wing on 3cell that weicghts up to 500g (HK Parkjet for example) and your the speedking on your local flyingfield.

Chamiso | Проверенный покупатель

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 24, 2012

excelente motor, mas deve ser instalado com um ESC de 30A

killlere | Проверенный покупатель

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Mar 15, 2012

Exellent motor

makes my falcon 3D rock

i orderd another one

cant go wrong withg this sucks less power then the original motor went from 4 to 5 minute flights to like 7plus with a 1300mah battery

Bezold | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Mar 09, 2012

I've been putting this off because I hate to leave a less than stellar review on hobbyking but here's what I experienced with this motor. First look, I received two 3.17 mm Shafts rather than both sizes advertised. This is fine since its the shaft I needed. Next, they were airplane shafts, net Heli shafts, the groove for the c clip was cut at the bottom instead of 2/3 of the way up so it was not possible to put a clip on. I planned on using this on a pusher jet so I needed to reverse the shaft, this required supporting the can with a piece of 1/8" pipe and heating the can with a torch before beating it out with a punch. Once all this was done I learned that the motor can't handle much heat. Burned out in ~90 seconds in flight with a 6x4 prop on a 3s battery. Went ahead and reinsulated the stator and wound it up with some RadioShack magnet coil wire to a slightly lower kv value and tried again. Same result. I'll keep it around, maybe rewind to original spec (mine arrived as 8 turns delta with six strand 28awg) and put it on my hbk3.

Helisang | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Sep 03, 2011

If you have money for to expend, you have to buy this motor. I recieve one of this, and the CNC motor head is deformed, Why Hobbyking not inspect the items of his customers?

Flugmodell | Проверенный покупатель

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Aug 30, 2011

no se puede usar para el HK250 demasiado grueso, shaft to strong fix in, dificult to change, se soltaron los imanes al tratar de cambiar lo y tenia que retificar el gujero eje, mas pegar los imanes y se doblo el chasis a si que!!!

santosc@netcabo | Проверенный покупатель

  • Overall
  • Quality
  • Value

Certified Buyer Rated

Jul 08, 2011

Use it on my blade 400 eflite, as a replacement motor. good performance

LARRYB | Проверенный покупатель

  • Overall
  • Quality
  • Value

Customer Rated

Jun 08, 2011

Purchased 2 of these motors.

They are great for there size but I would NOT recommend them for a 450 class heli.

Even with a 9 tooth pinion gear the motor still gets hot after 30 second flight. ESC also getting hot.

Put a meter on the motor and it is drawing 38A on the 450 with a 10 tooth pinion.

Larry

Файлы клиентов
KA400H Package Contents Download [3888]
Загрузить файл

Зарегистрируйтесь, чтобы загружать файлы.
пожалуйста войти в систему или Зарегистрируйтесь Начните помогать коллегам по хобби!