Micro HKPilot Mega Master Установить с OSD, GPS, телеметрия Радио, PDB БЭК Sensor / / Power (433Mhz) (APM)

• Overall
• Quality
• Value

For advanced users!

Jun 09, 2017

Took me some research to get it working. But finally everything ok. Here some important hints:

1. Do not load the APM 3.2.1 Firmware, use 3.2 instead. Mission planner will say "the board is retired" and propose automatically 3.2.1 - cancel this and you'll get 3.2.
2. Cable between OSD and HKPilot needs an additional Tx(OSD) -> Rx(HKPilot) connection. Otherwise OSD is not updating. For this you have to create you own cable.
3. For Firmwareupdate of the OSD use a 6 pin FTDI (USB-TTL) with CTL control output. Make sure the CTL-Signal is connected. Otherwise you get a "missing boot loader" error
4. For the OSD use the MinimOsd_Extra_Copter_Pre_release_Beta Firmware, based on firmware extra-2.4-r800. Can be downloaded here: http://discuss.ardupilot.org/t/minimosd-updating-gps-voltage-and-current/10391
5. Use external compass of the GPS. You have to cut carefully with a sharp knif on the PCB of the HKPilot at SJ10 between the two solder pads. There is no connection visible - anyway cut carefully until there is no connection between the solder pads measurable.

• Overall
• Quality
• Value

Customer Rated

May 21, 2016

faulty board for me! Only 4v get out from board to osd/mav-link and radio rx. No way to setup volt and ampere reading-monitoring; try every pin! Low voltage board allarm.

• Overall
• Quality
• Value

Customer Rated

Mar 09, 2016

Got this for my FPV 250. Good value for money. Sadly, I had to cut the link to get the external compass to work, and that was the last time I could communicate with the board. This is obviously a great board, but the necessity to cut a miniscule solder link proved too much of a hurdle for my skills, and I had to put it back into its box, and put it on the shelf. Hugely, disappointed that I couldn't get it working.

• Overall
• Quality
• Value

Customer Rated

Oct 09, 2015

Not Impressed with this kit, the Baro is not working even with foam and all precautions taken, I can only fly it in Stabilise mode and GPS modes, therefore cannot use the autotune and autotrim .... seriously annoying and disappointed for the price!

• Overall
• Quality
• Value

Customer Rated

Jul 17, 2015

Could not connect to mission planner using the rf module. Spent hours before I figured out that the rx and tx where switched on the cable going to the module from the APM. Hours of troubleshooting is not what I expect with a brand new product.

• Overall
• Quality
• Value

Customer Rated

Jul 08, 2015

Depus de conectar todo menos la telemetria y e osd me preparo para configurar el modulo de vuelo y no se comunica con el pc , e bajado los drivers del usb y los e instalado y sigue sin comunicarsen modulo y pc. podrian decirme como o donde puedo encontrar los drivers y como instalarlos?.
Gracias:

• Overall
• Quality
• Value

Customer Rated

Apr 22, 2015

First set keep sending bad compass health and bad Gyro Health and cannot calibrate the compass, returned to Hobby King for warranty claim but being ignore for 20 days. still no reply for HK, SxxT!
can't waiting hobbyking so buy second set, still bad compass health issue and still cannot calibrate th ecompass. anybody know how to fix the compass or this board is just a joke and never can use???? Try both built in and external compas still failed...........

• Overall
• Quality
• Value

Customer Rated

Apr 17, 2015

Very bad, my copter is crashed every time. Bad bad bad.
I use the best component, Tmotor motors, simonk ESC, Frsky... this flight controller is so bad friends

• Overall
• Quality
• Value

Customer Rated

Apr 02, 2015

They sent me a defective!
I waited a month before they wrote back and told me to wait again a month
Hobbyking are crooks !!!!
Never with them do not purchase.
In other stores Honkkong or china respond to mails within 24 hours are
Hobbyking and pathetic after 2 weeks.

• Overall
• Quality
• Value

Customer Rated

Mar 16, 2015

Excellent Product! Ive purchased a few HKPilots and APMs in my Multirotor quests and this is the smallest yet works just the same as the larger 2.5 - 2.7 variants. In my opinion, I think this is so much better and easier to work with. Great savings on weight and really makes room for a good fit in my QAV280. I would prefer that it came with the pins uncrimped as I had spent quite abit of time trimming down the wiring which came a little too long for mini quads. Yes, Ive literally used up everything that came with this package. Nothing left unplugged. I'll try to post up pictures in the 'Files' tab to show you how I managed to rewire it neatly.