Мини-FU-BAR V5.3.4 3-Axis Flybarless система управления вертолетом

• Overall
• Quality
• Value

Customer Rated

Jun 26, 2013

it flys awesome, just like the real one. When will HK provide the BT-Cable for it ???



Please provide a cheaper version without the USB Interface, as I have 4 Fubars with 4 USB Interfaces now ! I dont need anymore interfaces.

• Overall
• Quality
• Value

Customer Rated

Jun 25, 2013

Just wanted to add that I do have a bluetooth module working with the fu-bar
you will need a mini-b usb connector and a bluetooth module but it does work

so now its perfect

• Overall
• Quality
• Value

Customer Rated

Jun 24, 2013

installed this on my 450pro and wow
it is exactly like my 300.00 controller on my 600pro
only difference is it doesnt have a port for bluetooth
if it did it would be perfect

This is the only controller anyone flying FBL heli's should buy

• Overall
• Quality
• Value

Customer Rated

Jun 24, 2013

Zum Rating:
Es ist total dmlich zur einen Seite die Servostecker zu verbauen und gegenberliegend den USB-Plug fr die Programierung, da der Stecker fast genau so lang ist wie das Gehuse selbst. Der Stecker selbst ist wieder Irgendwas, aber kein micro/mini USB etc.
Weiterhin fehlt die Blauzahnverbindung, so das sich der Einbau trotz des kleinen Gehuses als problematisch erweist. Die Verarbeitung ist OK.
Die Patchkabel sind ordentlich und sogar an den Steckern beschriftet.
Es liegen 3 sehr dnne Klebepads bei, ich hab die vom Microbeast verbaut.
Es wird keine Software mitgeliefert, dass Teil ist ein 100pcnt Klau vom der V-Bar, allerdings ohne die kleinen Features wie USB von oben und Bluetooth.

Habe grade das Fubar in einen T-Rex600 EFL eingebaut. Die Singellineverbindung zum M-Link RX-7-DR funktioniert auf Universal Digital Input perfekt, damit bleiben noch Steckpltze fr den Ext. Governer brig. Mein Drehzahlsensor vom Eagletree scheint nicht zu laufen, werde noch mal einen von Hyperion probieren. Wie andere hier schreiben, soll der Ext.Gov. da Pro-Version zu funktionieren.

Mein Fazit: Wer Wert auf komfortable Bedieung, Support und Softwareupdates legt, sollte lieber 100.- drauflegen und sich das Orginal gnnen. Und ein gutes Gewissen gibts auch noch mit dazu.

• Overall
• Quality
• Value

Customer Rated

Jun 20, 2013

o stars.no software ,spent 3 hours searching for software.hobbyking u should pay me 359$for wasting 3 hours of my life on this item

• Overall
• Quality
• Value

Customer Rated

Jun 19, 2013

I can now confirm it works really well with electric governor, installed a hobbywing phase sensor on my trex 500, with scorpion 4015, 2700 hs. 13 degress pitch...What a beast is my word for it...Remember folks - pole should be down, opposite to mini vbar, so when u install the phase sensor contact it should be at bottom.

Regards David

• Overall
• Quality
• Value

Customer Rated

Jun 18, 2013

i'm the proud owner of 3 v-bars 2 ikons 1 zyx-s and now 2 fu-bars

the are software wise just like the v-bar with the exception there is no way to plug in a bluetooth connector (sorry)

aside from that i've yet to find any software that will work with it other than v-bar software and unless you have the 5.3.2v that doesnt phone home good luck

I will be doing some test flights this week and will keep all updated

• Overall
• Quality
• Value

Customer Rated

Jun 11, 2013

Been flying the original product for nearly 4 years,i swapped one of their units for the Fu bar onto my 6hv,loading the same setup file into it and the model flies just as well.

Low cost,high performance flybarless has arrived.

• Overall
• Quality
• Value

Customer Rated

Jun 10, 2013

Can confirm it feels like a real vbar. U should know it shouldnt be run in cold weather r/t sensor quality. The controls is very crisp. Had not tested the governor yet, but will do as soon i get my other one to test with castle esc.

• Overall
• Quality
• Value

Customer Rated

Jun 07, 2013

Received my fu-bar and opened it up - internal soldering quality is A1. Would trust it with any other brand.



Mounted it first on my 6S Tarot 450 pro heli with HXT900 analog cyclic servos - flew very well indeed.. as good as any other fbl gyro i've had on this heli.. and iv'e had several!!!



Took it off an put it on my new gaui NX4 nitro heli - flew it today.. flew superbly.. can inverted piro dead flat many times - flew true and no issues. only issue i had was some small tail artifact vibes and that's due to me hard mounting the fu-bar on my heli with cheap $2 tape.. the tail vibe/twitch is nitro related and so small i'm not ging to worry about it - good mounting tape will see it gone i'm sure...



My NX4 flew great straight off the bench setup - no tweaking.. just lowered my tail gain 2pcnt and that was it...



Great gyro, great workmanship and build quality - what more can i say..



Trustworthy on any side heli it's meant for..