НТН-600 является очень быстрым и совершенно законченный V-Hull гоночной лодки и поставляется с мощным 2881kv водяным охлаждением бесщеточный двигатель и аппаратного обеспечения.
Все оборудование включено и хорошо обработанная, закончил в шариковой дутья и анодированного для предотвращения коррозии.
Вам понадобится 4000mAh 3S или больше & 50A ESC для питания этой лодке полной скорости.СпекуляцияДлина: 675mmШирина: 155ммВысота: 100ммВес: 990gМотор: 28-58 размер 2881kv Водоохлаждаемая бесщеточныйESC: 50A с водяным охлаждением (обязательно)Система привода: 3.18mmНеобходимые.
Система радиосвязи (2ch) и приемник
1 х 3кг стандартного размера серво4000mAh 3S 20C Lipo
50A ESC* Запасные части, прибывающие в ближайшее время.
Вес ( г )
The Photos in the listing do not show a true representation of the item !
The listing shows a 'Stepped Hull' but in fact the hull is not stepped it s only smooth. This difference is a huge issue regarding the true value of the Boat ! and very poor when it comes to being able to trust what the listing shows when deciding upon making the purchase of other Hobby King Product !I bought this boat despite negative reviews. The first thing I did was to replace the prop with an Octura642 3/16" drive. I purchased a 3/16" to 1/8" prop adapter from USA, couldn't find one in the UK. I Powered it with a 4000mah 3C Lipo not the best of fits, but set it as far forward as the motor mount will allow. I had to balance it out by adding 260gms of lead to the servo side. It allows water up the flex shaft but noticed that there was a large gap between the dog drive and the flex shaft tube carrier. Removed this gap by tightening the prop and forcing the dog drive up the shaft to close the gap. Need to test water ingress but am confident that this mod will reduce it. The water cooling is useless, it is very difficult to blow through the inlet to outlet so water flow stands no chance. There are no kinks in the piping, I will therefore have to run an alternative cooling method. However with this setup and a little prop drive angle tuning it is fantastically fast and sits nicely on the plane. A joy to own and pilot.nice boat, didnt tested it yet , but looks greatBought this for a friend as his first boat. Only had a 120A ESC left that supports down to 3Cells, so maiden was with 3S and it went pretty fast, stable and with no water in it after 5 minutes. Then we tried a 3 blade prop which resulted in very low speed. Next attempt was a 4S 4700mah - THIS IS FUN LIKE HELL! At least with the original 2 blade prop, with 3 blades it only flys around in the pond in all directions. And no overheating - regardless that the watercooling does not work! The concept is a bit overkill, standard inrunnercooling AND motormount as well, but it does not work even with only one cooling connected. I think about replacing the inlet. After a few runs the mount for the lipo broke down but can easily glued in again. For the money and with a bit of experience it's good fun!The only thing this boat is quality finish, the rest is crap, poor stability, recommended battery is too heavy for the size of the vessel at high speed it tends to sink, too much water enters the telescope despite spending grease regularly , already burned two servants to enter the water. I do not recommend buying this product hobbyking because no one plays good fun. To give you an idea of how bad the boat, the telescope it is on a slope below the float level of the boat, which facilitates the entry of water through the telescope.Otima Lancha...
Acabamento de primeira, veio muito bem embalada e sem nenhum problema estou usando como ESC um Aquastar 120A. recomendo a compra desta maquina... simplesmente perfeita!Hi.
I have no runed this boat a few times. As some other says, the 50a esc fail after 5 minutes of 11,1v run. I have no switch it with a Turnigy marine 60A. I have not nailed it in yet, so its wery unstabel i high speed. I have plans of laying som lead sheets in the bottom in back of the boat. It is plowing to mutch, so some weight in the back is nesesary. The prop is blunt, so I'm going to switsh it with a balansed prop from grimracer.Buena lancha, precio normal.
Es muy tcnica y algo compleja de ajustar, como viene de serie no navega bin, requiere bastante ajuste de pesos y modificar la posicin de batera, el capatador de refrigeracin, ngulo de helice y timn.
Una vez bin ajustada navega decente, un peln escasa de motor, pero es una pasada como se agarra en el agua.
Ha costado un poco de trabajo centrar bin todo, pero ahora va genial !!!!!!This is a great looking boat, I have not run it yet as I am waiting on my lipos. I've done the bath test and had a bit of water comming in but that was easily fixed with some sealant. I will be changing the esc to a 60amp and maybe the motor to run it on 4s. I would definately reccomend this boat if you like the scale model look.