SU47 Твин 55mm EDF Jet (KIT)

• Overall
• Quality
• Value

Certified Buyer Rated

Aug 27, 2013

Pas facile pas conseill aux dbutants

• Overall
• Quality
• Value

Certified Buyer Rated

Feb 16, 2013

low price for high class and good quality

• Overall
• Quality
• Value

Customer Rated

Jun 01, 2012

Attention!
I bought the engine for the aircraft to the shaft of 2.3 mm as it is written in the description.
Collet which is sold bundled with edf can be mounted on a shaft with a minimum size of 3 mm.

• Overall
• Quality
• Value

Customer Rated

Oct 02, 2011

I haven't receaved my plane yet but have ben reading alot on it and it sounds like a good buy can't wate to get mine

• Overall
• Quality
• Value

Customer Rated

Sep 12, 2011

fixed 2x 4.3k out runner motor, power shld be enough to lift the plane. look through the manuel but unable to find the c.g. anyone can share the c.g of this plane? thanks

• Overall
• Quality
• Value

Customer Rated

Aug 04, 2011

Update-Aug 2. I modified the airframe to accept a single fan just ahead of the area for the original two fan position. I used the T-2815 4800 KV with a 40 amp SC and a 2200 Nano. Internal ducting was easy using depron and plastic pop bottle parts with the twin exit/efflux tubes reduced to the same size of other single fan setups. No dead weight but I did fill the flimsy nose cone with expanded Gorrila glue. Excellent flight performance, easily over 100kmh, rolls perfect and lands well with a little power on. Easily my favorite jet now.

• Overall
• Quality
• Value

Customer Rated

Jun 28, 2011

OK, so this is not a good first EDF, I have gone through a series of misfortune and after making some repairs I have finally flown this. I have found the CG needs to be roughly 1/2 to 1" back from the wingtips. Since up elevator creates the effect of a aileron up wing spoiler as everything is connected by linkage. I have found that it helps to have some amount of down aileron at nuetral elevator so you get a flaps effect. This thing needs speed to get airborne so get some good esc's with heat sinks and some powerful motors. I had to use a 1300 Mah 3 S battery to get it off the ground and it was admittidly a short flight. If you wanted to have separate aileron servos and evelavtor servos the added weight in the back may help with the balance. It flew nicely once airborne. The one rock got sucked up and broke a fan blade so it didn't have the power it should have butwith high nose up I had good control. I'm thinking about buying a second kit now that I have some of the basic info to help it be more succesful. Hope you get one and sort it out so we can all learn from your efforts. !!!

• Overall
• Quality
• Value

Customer Rated

Jun 20, 2011

I got this plane from FIY in ARF mode.

Built in less than 45min.

The stock EDFplusESC responded very well to 2.2 nano-tech 25C & Turnigy 2.2 20C.

The plane flies excellent, the only weak point is the front landing gear that is easily broken. I glued a piece of plywood with a hole to replace the plastic one.

Manouverability is superb. Rolls are absolutely axial, no bad tendencies.

Landings need to be done carefully with some speed .

• Overall
• Quality
• Value

Customer Rated

May 26, 2011

Have had the pleasure of having two of these Used Hk foam safe and HK five minute eoxy. Hk esc, KMS inrunners from phase 3 F-16 Caorona 4ch synth RX Turnigy 9X TX.

Both hit the ground not on purpose. Cg no brainer built in with the placement of the battery tray 2200 HP 3S easy ROG.

Do not think I will try another

will probably put the power set in an A-10 kit

Happy landings

• Overall
• Quality
• Value

Customer Rated

May 11, 2011

I RECEIVED MY SU-47 KIT,IT APPEARS WELL DESIGNED,PARTS FIT PROPERLY.

THE ONE OBSERVATION HERE IS THAT THE EDF UNITS SUPPLIED WITH THE KIT ARE UNAVAILABLE ,THEY ARE DIFFERENT FROM THE USUAL 55 EDF UNITS IN A FEW IMPORTANT WAYS,IS THERE A WAY I CAN PURCHASE TWO ADDITIONAL UNITS,I DO NOT WANT TO USE A DIFFERENT STYLE UNIT.

Thanks

mike

mwb8345a@aol.com

Try to include as much data as possible.