Зарегистрируйтесь

Product Finder

Настройки

Useful links

Живой чат
 
[["US","AU","GB","DE"]]
Зарегистрируйтесь
Shipped From:
  • USA

Turnigy B12-30 4100kv Inrunner

Turnigy B12-30 4100kv Inrunner

Discontinued Product

Please continue searching for a similar product.
Stock:
OUT OF STOCK
Вес:
39 g
Артикул:
TR-B1230-4100
Описание
товара

Также известный как класс двигателя 130S. TR-1230 является отличным двигателем для небольших EDF или Direct Drive appications. Подумайте типа мини парк реактивных или небольшой EDF для самолетов GWS.

Спекуляция
Kv: 4100rpm / V
Мощность: 32W
Включает: 17
Сопротивление: 732mh
Ток холостого хода: .2A
ESC Требуемый: 10A
Конфигурация Липо: 2-4Cell (от 7,4 до 14.8V)

Габаритные размеры:
Диаметр: 12 мм
Может Длина: 30 мм
Длина вала: 10мм
Вал Ширина: 1.5mm
Передние расстояние Маунт: 8.5mm
Передняя гора Тема: M2
Вес: 18г

Product
Specifications

Дополнительная информация

  • Артикул:
    TR-B1230-4100
  • Brand:
    Не применимо
  • Вес ( г )
    39.00
  • длина
    0.00
  • ширина:
    0.00
  • Высота:
    0.00
  • Kv ( об / об)
    4100.00
  • Max Токи (A)
    0.00
  • Мощность (Вт ):
    32.00
  • Длина В ( мм ):
    31.00
  • Может Длина D (мм )
    30.00
  • Максимальное напряжение (В )
    15.00
  • Вал А ( мм):
    1.00
  • Unit Weight (g):
    18
  • Диаметр С ( мм )
    12.00
  • Общая длина E (мм )
    41.00
  • Сопротивление ( тк ):
    732.00
Community
Discussions
Rate&
Review

Напишите ваш собственный отзыв

Only registered users can write reviews. Please, sign in or sign up

verified_user Quality
trending_up Value
playlist_add_check Overall
Don't know why but the shaft broke right where it was machined down. Did not have much time on this motor and did not get $8 dollars worth out of it either. Not sure if the blade was out of balance. I switched to a Blue Arrow BL1230 for now. Maybe I'll try the Turnigy B12-30 3850kv later.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Got this motor even after reading all the reviews.

hooked it up on the bench to test before installing in my Gravity/Cox spitfire. Put oil in the bearings put on GWS 3x2 prop an used 2S 500ma lipo for the first run. Started it up on bench an all seamed fine. Then the motor got loose and the prop bumped the bench. The motor shaft broke off flush with the case. Sure am glad I did not get it all installed before I found out how soft the shaft is. Verry disappointed with this motor. I cannot reccomond it. I have another Cox P47 warbird with a medusa research motor that has been crashed hard several times and never had a problem with it flys great vwery fast. Spend a little more for the better quality.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great little motor - using this on a Eagle 50 (aka Walkera 22e) direct drive tail with a Esky Tail Blade Set 002386. The tail balde is the same as the BLADE EFLH1321, GWS 3x2 prop and also the HCB-03 from HobbyKing. I got a BLADE EFLH1321 mount and flipped it 180 so the the air flow is across the motor and with the addition of a heat sink the motor runs much cooler. I paired it with a Tz12A HobbyKing 12A BlueSeries brushless controller plugged into Assan GA-250 gyro and a walkera RX-2609 receiver that had the gyro mod (gyro board removed and gyro-sense jumper to AUX2).
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
I bought this for a losi 1/24 rally. It works great. good speed and power and barely gets warm with 3 cell lipo with 17t pinion and 53t spur. awesome! I would definitely recommend!!
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Great brushless. Used in losi 1/24 4wd rally. Wish it came with connecters soldered. Also used turnigy 18A esc w
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
YA HICE UNA PUBLICACION POSITIVA, PERO COMO DATO ADICIONAL, EL
A 10 QUE VA MONTADO CON FAN DE 50MM LO ESTOY VOLANDO CON
4S, RHINNO 1000MAH ,30C.
LOS ATAQUES EN PICADO QUEDAN MUY LINDOS.
SALUDOS DESDE URUGUAY................FLAVIO
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Not what I expected. Bearings are not good.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
buen motor, esta montado en un gws a 10 con fan de 50mm. y lo lleva de maravilla.

saludos desde ururguay..........flavio
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
Runs little bit hot on 3S with GWS 60x25 prop, mpst like too high kv for this setup, need to order less kv motor as i like these.
verified_user Quality
trending_up Value
playlist_add_check Overall
verified_user Quality
trending_up Value
playlist_add_check Overall
great little inrunner. perfect for the gws 40mm ducted fan. I strongly recomend getting a heat sink.
verified_user Quality
trending_up Value
playlist_add_check Overall
View all reviews
Upload
Videos
Upload video
Upload
Files

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Метки товара

Используйте пробелы для отделения меток. Используйте одинарные кавычки (') для фраз.