New Items ФОРУМ
Зарегистрируйтесь

Итоговая цена

0,00 руб.

Cart 0 Cart 0 Loading...

Turnigy электронный привод 4030/10

Turnigy электронный привод 4030/10

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
e-drive-4030/10
WANT FREE SHIPPING? Click here to find out more!

Turnigy электронный привод 4030/10

Спекуляция
Количество клеток:
4 ~ 7 х литий-поли
RPM / V: 385
Максимум. КПД тока: 20-40 А (> 78%)
Нет тока нагрузки: / 2.1
Текущая емкость: 50A / 60 - е годы
Размеры: 40х30 мм
Диаметр вала: 6 мм
Вес: 367g
Рекомендуемый вес модели: 3000 ~ 4450 г
Рекомендуемая опора без коробки передач: 13 "-16"

Рекомендован Setup.
14x7 Thin проп с 5 ~ 6S, которая дает 4850g тяги.

Щелевого типа.
Тренер: до 5500G
3D: до 3000г
Спорт / Aero / Warbird: 4000 г
Формула: +0,60 IC свечение двигателя



Все двигатели включают карданный адаптер, разъемы и монтажные аксессуары.

  • Артикул e-drive-4030/10
  • Brand -
  • вес 367.0000
  • длина 0.00
  • Packaging Width 0.00
  • Высота 0.00
  • Kv ( об / об) 385.00
  • Max Токи (A) 40.00
  • Сопротивление ( тк ) 0.00
  • Максимальное напряжение (В ) 25.00
  • Мощность (Вт ) 0.00
  • Вал А ( мм) 6.00
  • Длина В ( мм ) 70.00
  • Диаметр С ( мм ) 49.00
  • Может Длина D (мм ) 33.00
  • Общая длина E (мм ) 83.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Just finished some bench testing on this motor:

Rm: 0.047 ohm (measured between any two motor leads)

Kv: 348 to 376 [rpm/volt] depending on controller advance (4-30 degrees)

Io: 1.05 to 1.30 [amps] @ 12.6v depending on advance (4-30 degrees)



Motor came without connectors. Motor is well ballanced and has some flux leakage from the motor can. No funny noises. 12 tooth stator with a 14 pole rotor.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Just finished some bench testing on this motor:

Rm: 0.047 ohm (measured between any two motor leads)

Kv: 348 to 376 [rpm/volt] depending on controller advance (4-30 degrees)

Io: 1.05 to 1.30 [amps] @ 12.6v depending on advance (4-30 degrees)



Motor came without connectors. Motor is well ballanced and has some flux leakage from the motor can. No funny noises. 12 tooth stator with a 14 pole rotor.

I just got this motor last week and have tested it with a few different props. I have it mounted on a .60 size P51 Mustang, at first I tried a 14 x 7 thin prop and got 7000 rpms on 6 lipos, I then tried a 14 x 7 APC and got around 6800 rpms. This would of been good on a lighter plane but this plane is pretty heavy. Then I tried a 15 x 12 on 6 lipos and that did the job. The only negative was the thin prop shaft on adapter and loose fitting nut.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I just got this motor last week and have tested it with a few different props. I have it mounted on a .60 size P51 Mustang, at first I tried a 14 x 7 thin prop and got 7000 rpms on 6 lipos, I then tried a 14 x 7 APC and got around 6800 rpms. This would of been good on a lighter plane but this plane is pretty heavy. Then I tried a 15 x 12 on 6 lipos and that did the job. The only negative was the thin prop shaft on adapter and loose fitting nut.

I'm using the 4030/10 in a CMPro P-26 Peashooter. Batteri 6S 5000mAh Lipo and a 14/7 thin prop. The engine is pulling around 5 kg thrust and is running very smooth. Best buy at that price. 5 Stars from me

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I'm using the 4030/10 in a CMPro P-26 Peashooter. Batteri 6S 5000mAh Lipo and a 14/7 thin prop. The engine is pulling around 5 kg thrust and is running very smooth. Best buy at that price. 5 Stars from me

Very nice looking motor but it also has plenty of power! On my test stand I got the following results using my eagletree data loger:

Battery: 10S A123 2300mah cells 36V(all I had on hand for testing)

ESC: Turnigy Sentilon 100A HV

Prop: APCE 16X8

Full Throttle: 1200 watts @ 35amps

RPM works out to around 13,000 (batt voltage under load X KV of the motor)

After a 30 second full throttle run motor was warm but I wouldn't say hot at all. Next stop for this motor is the nose of my 4 meter sailplane!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Very nice looking motor but it also has plenty of power! On my test stand I got the following results using my eagletree data loger:

Battery: 10S A123 2300mah cells 36V(all I had on hand for testing)

ESC: Turnigy Sentilon 100A HV

Prop: APCE 16X8

Full Throttle: 1200 watts @ 35amps

RPM works out to around 13,000 (batt voltage under load X KV of the motor)

After a 30 second full throttle run motor was warm but I wouldn't say hot at all. Next stop for this motor is the nose of my 4 meter sailplane!

Just received this motor as a replacement for the other one I have. I just wanted the prop mount adapter because the threads stripped on the previous one. NOW THIS ONE stripped too. this a serious design flaw. I do not recommend this to anyone else unless you want to have your plane to had a prop strip in mid flight.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Just received this motor as a replacement for the other one I have. I just wanted the prop mount adapter because the threads stripped on the previous one. NOW THIS ONE stripped too. this a serious design flaw. I do not recommend this to anyone else unless you want to have your plane to had a prop strip in mid flight.

First. 6s at 375kv max RPM is 8250 - NEVER 14x7 prop and 5 rg thrust!!!



I use this motor with 6s 4250mA + Turnigy Plush 80 with 14x7 thin prop - above 2.3 kg thrust. APC-E 16x8 and 15x10 props give 3-3.2 kg thrust and maximum 32...34A... Hmmm... I whant more! But I can not use more than 6s....



HobbyKing! What prop give 4 kg thrust on this motor and 6s?

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

First. 6s at 375kv max RPM is 8250 - NEVER 14x7 prop and 5 rg thrust!!!



I use this motor with 6s 4250mA + Turnigy Plush 80 with 14x7 thin prop - above 2.3 kg thrust. APC-E 16x8 and 15x10 props give 3-3.2 kg thrust and maximum 32...34A... Hmmm... I whant more! But I can not use more than 6s....



HobbyKing! What prop give 4 kg thrust on this motor and 6s?

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!