Become a Dealer Blog
Language
ENG
USD
Selected Country:
[["US","AU","GB","DE"]]
    Register

    Total Price

    $0.00

    Cart 0 Cart 0 Loading...
    Display : All categories 7 Aircraft 1598 Drones 480 Speed Controllers 6

    Turnigy Multistar USB BLHeli Programmer For V2 Multistar ESC

    Turnigy Multistar USB BLHeli Programmer For V2 Multistar ESC

    You will earn 1 bonus points for buying this item.

    Generating Links

    Turnigy Multistar USB BLHeli Programmer For V2 Multistar ESC

     
    Price:

    Now save save $5.74 $5.74

    Special Price $1.81 $1.81

    You save save $5.74 $5.74

    Was  $7.55

    Already Purchased Discontinued Product

    Please continue searching for a similar product.
    1 year warranty
    SKU:
    9351000056-0
    Discontinued Product
    Please continue searching for a similar product.
    want FREE shipping? Click here to find out more!
    Report Issue Not Cheapest?

    Copy and Share the Below URL

    Product Description

    The Multistar USB tool for all V2 Multistar ESC’s. Multistar ESC's feature an ATmega MCU that opens the door to customizable firmware – The V2 Multistar comes with BLheli software pre-installed, and for those so inclined this easy to use USB tool is available for Configuration and updating via the BLHeli Suite GUI. This allows you to easily reverse motor direction without changing motor wires, adjust a host of setting to include Demag compensation and timing for Hi-KV motors with Sync issues.

     

    MultiStar ESCs are a quality speed controller at a fantastic price! Designed for simple installation and easy setup these ESCs have proven to offer excellent performance when used in Multi-rotor applications. If you're starting out in Multi-rotors and need an easy to install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered.

     

    To use the programming tool simply download the free BLHeli suite software plug the USB tool into the computer and select the comport, next connect the receiver connection wire from the ESC to the USB tool and turn power onto the ESC. Press connect and adjust parameters as needed and select flash and you’re done.

     

    Note: The tool is for the Multistar V2 series of ESC and use with BLHeli suite GUI software, And is not compatible with other ESC’s.

    Product Specifications
    Videos
    Upload video

    Only registered users can upload video. Please, log in or register

    Discuss 0
    Topics
    Sort by
    Most Recent Topics
    * Nickname:

    * Your Reply:


    Please, enter the text shown in the image into the field below
    CAPTCHA Image
    *Verification Code:
    Cancel
    Submit
    Post a new Topic
    * Nickname:

    * Your Topic:



    Please, enter the text shown in the image into the field below
    CAPTCHA Image
    *Verification Code:
    Post Topic
    Reviews

    Only registered users can write reviews. Please, sign in or sign up

    Ran D. | Verified Buyer

    • Overall
    • Quality
    • Value

    It works as intended, but minus one point for the lack of instructions.

    Apr 22, 2018

    Ironically, I came here to give it a bad review due to lack of instructions, and then I found the instructions I needed in the reviews. It works as intended, but minus one point for the lack of instructions.

    lampo.ep | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Feb 04, 2016

    turnigy buenos productos y bajo costos

    fotod | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Sep 30, 2015

    Fantastic item, I use it all the time in all places and electronics. Nice n shiny finish, good covering finish.

    QuadroMania | Verified Buyer

    • Overall
    • Quality
    • Value

    Customer Rated

    Sep 29, 2015

    LHeli with 15A Multistar ESC with Multistar USB Tool

    - BLHeli: https://blhelisuite.wordpress.com/

    - Multistar USB Tool with out reed wiere!

    - De Multistar ESC feed with 5Volt from ext.BEC!

    -
    Settings BLHeli

    1. install the driver

    2. start BLHeli Suite

    3. Select Amtel/Silabs Interface = 1 Amtel BLHeli Bootlader (USB/Com)

    4. Plug in USB programmer into your computer

    5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]

    6. Select the correct speed (Baud 9600)

    7. Connect ESC plug into USB programmer (without the red cable !!!)

    8. Click on Connect

    9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)
    -
    Eanable One Shot in BL Heli


    - PWM Frequency/Damping = Light

    - Motor Timing = High

    Feldsalat | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Feb 06, 2015

    Einwandfreie Funktion mit den 6A V2 Reglern.

    LeBobo | Verified Buyer

    • Overall
    • Quality
    • Value

    Customer Rated

    Feb 03, 2015

    Works fine.
    I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire of the USB programmer and to power the ESC from a BEC 5V.

    Procedure (to combine with LeBobo's MultistarV2 Pack ) :
    1. install the driver
    2. start BLHeli Suite
    3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
    4. Plug in USB programmer into your computer
    5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
    6. Select the correct speed (Baud 9600)
    7. Connect ESC plug into USB programmer (without the red cable !!!)
    8. Click on Connect
    9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

    LeBobo | Verified Buyer

    • Overall
    • Quality
    • Value

    Customer Rated

    Feb 03, 2015

    Works fine.
    I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire and power the ESC from a BEC.

    Procedure (to combine with LeBobo's MultistarV2 Pack ) :
    1. install the driver
    2. start BLHeli Suite
    3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
    4. Plug in USB programmer into your computer
    5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
    6. Select the correct speed (Baud 9600)
    7. Connect ESC plug into USB programmer (without the red cable !!!)
    8. Click on Connect
    9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

    pawcio0928 | Verified Buyer

    • Overall
    • Quality
    • Value

    Certified Buyer Rated

    Jan 14, 2015

    I use this USB programmer with Multistar 10A and I haven't got any problem.

    transalpin | Verified Buyer

    • Overall
    • Quality
    • Value

    Customer Rated

    Dec 06, 2014

    It is not a programmer for Multistar, it is a universal programmer from Multistar.
    The stick has always worked with BLHeliSuite, with ANY Atmel based ESC, which has the small 512 bytes BLHeli bootloader flashed over ISP (and which do not have an inverted input, like the Multistar V1 ESC have). It has NOT been specially build for Multistar ESC nor is it somehow bound to work only with Multistar ESC.
    All the negative reviews address the Multistar V2 ESC, not the this Multistar programmer.
    As far, as it tested, it works great and is easy to use.
    The best solderless ready-built adapter for the small 512 bytes BLHeli bootloader (or other 1-Wire AVRootloader solution).

    Manuals/Files
    Customer files
    Connecting_ESC.png Download [601]
    Upload your file

    Only registered users can upload files.
    Please log in or register to start helping your fellow hobbyists today!

    Need Help
    Live chat

    © 2024 HobbyKing. All Rights Reserved.

    Trustpilot