12 Channel Tx/Rx video system with CCD camera.
The camera uses a quality glass lensed SONY CCD camera system and a high power 1000mW transmitter.
Unlike other generic systems, we have produced a wiring loom and included it with the camera so that the Tx and camera will be compatible and on the same voltage.
If you buy your camera and Tx seperately the plug polarity and voltages may be very different.Included.
1 x SONY CCD 1/3inch Camera
1 x 2.4GHz 12 channel Video Transmitter (1000mW)1 x 2.4GHz 12 channel Video ReceiverCamera spec.CCD sensor type:1/3 color SONY CCD
NTSC: 510(H)*492(V) (Included)
Scanning system: Interlaced scanning
Horizontal resolution: 420TV line
Minimum Illumination 0.01LUX/F1.2
S/N Ratio: 48dB
Gamma Modification: 0.45
White balance: Auto
Auto backlight compensation: Auto
Input voltage: 9~12.6V
Electric current 80MA
Electronic Shutter: 1/50 (60) ~ 1/100,000s
Video output: 1.0VP-P composite video
Operation Temp.: -20~50
Flight time: Approx 60min/100mah 3SFPV Tx Spec.
Channel: 12-Ch, AV synchronization
Input voltage: 8~12V
Weight: 78.5gSize: 73x40x14mm
I purchased this system as my first ever FPV system. Im I major noob to fpv and was able to hook it up in a hour, the only thing wrong with the system on mine the camera plug in was backwards and had to be flipped. It has excellent video quality, although i have only bench tested it seems to not break up very much and has a strong signal.PLEASE NOTE: MY CONNECTOR THAT WENT INTO THE CAMERA WAS BACKWARDS. There have been other people who have reported the same problem. When I originally fired up the camera system, my 7" LCD screen showed me a flat line. In the end it was because the connector that plugged into the camera was wired backwards. If you snap off the back of the white plug on the camera, it will plug in the right way. You can tell by making sure the wires go to the right part of the camera so goes to red, - goes to black and "vid" goes to the white wire.I purchased 2 units. Both transmitters fried . Bad quality. I used 3s battery and just worked for 3 minutes.DO NOT CONNECT A BIG LIPO. I WAS USING A 3S LIPO 1000 MAH 10C AND EVERYTHING WAS FINE. THEN I PLUGED IN MY 4000 MAH 20C LIPO AND SPARKS AND POPING NOISES CAME OUT MY TRANSMITTERGood product, the connector was on backwards on the camera resulting in it not working properly but whatever i just pulled the plastic bit off put it back on upside down and it works fine.System arrived in excellent condition, packing was a bit thin but was then packed in larger box more properly. Non-North American plug is easily changed, or just get another power supply/battery. Tx and camera both get mildly warm during operation. Included wiring harness is very convenient. Camera seems to give fairly decent picture, given price. Given specifications quite far off from actual specifications, though this was somewhat expected. Especially the TX weight. Haven't flight tested or range tested yet.
Some extra details:
Camera: 11 g
TX: 76 g
Antenna: 10 g
Wiring Harness: 6 g
Total Airborne: 103 g
Camera: 110mA @ 12.0V
I also made some measurements with a spectrum analyzer:
Channel Bandwidth: 16MHz @ -40dB
Channel | Center Freq | TX Cam Current
| (GHz) | (mA @ 12.0V)
0 2.4109 405
1 2.4308 365
2 2.4500 365
3 2.4703 470
4 2.4903 470
5 2.5105 460
6 2.3905 430
7 2.3708 525
8 2.3510 535
9 2.3315 535
H 2.3120 540
C 2.2915 540
It is interesting to note the variation in current draw depending on the channel. Didn't have an opGreat product for the price! Very easy to change the AC plug for use in USA. I found the range to be around 950yds (good weather). Tx is around 91g! not 29g. More details about this product at FPVaviation.com. Video review soon to follow!1000mW
Got the system a couple of days ago, measured he total current of camera and tx to 350mAh!
Not the best camera but ok for its price, struggeling a bit with adjusting in snowy landscapeI would have given it NO stars but one was the lowest. I got mine in August with a damaged camera. There was no padding anywhere in the package and the camera was crushed lens-first into the bottom of the box. Because returns are sometimes cost-prohibitive, HK does not properly pack all items for international shipping in hopes that the customer will just eat the cost and replace it themselves rather than paying out of their pocket to return ship the broken item and then waiting another month to receive their replacement. I've ordered lots of stuff from HK and this was my only damaged order but rarely if ever do I see any packing material and I assume it will happen again.Este kit, el chaw fun y el kung fu es lo mejor que hicieron los chinos.
Funciona muy bien. Tengo un Futaba PCM de 72Mhz y podes alejarte 1Km sin problemas. Es muy importante las posiciones de las antenas de TX-RX Video para una buena seal.