12 Channel 900Mhz Tx/Rx video system with CCD camera.A high power 1500mW Tx on 900mHz ensures a very long signal range!Unlike other generic systems, we have produced a wiring loom and included it with the camera so that the Tx and camera will be compatible and on the same voltage.
If you buy your camera and Tx seperately the plug polarity and voltages may be very different.Included.
1 x SONY CCD 1/3inch Camera
1 x 900Mhz 8 channel Video Transmitter (1500mW)1 x 900Mhz 12 channel Video ReceiverCamera spec.CCD sensor type:1/3 color SONY CCD
NTSC: 510(H)*492(V) (included)
Scanning system: Interlaced scanning
Horizontal resolution: 420TV line
Minimum Illumination 0.01LUX/F1.2
S/N Ratio: 48dB
Gamma Modification: 0.45
White balance: Auto
Auto backlight compensation: Auto
Input voltage: 9~12.6V
Electric current 80MA
Electronic Shutter: 1/50 (60) ~ 1/100,000s
Video output: 1.0VP-P composite video
Operation Temp.: -20~50
Flight time: Approx 60min/100mah 3SFPV Tx Spec.
Channel: 8-Ch, AV synchronizationPower: 1500mW
Input voltage: 12V
Weight: 18gSize: 73x41x14mm
Frequency: 0.9G 0.910G,0.980G,1.010G,1.040G
Once I changed the red and white wires going into the camera it worked superbly. The reason for four crowns on quality is due to needing to change the camera plug even though the narrative in product description states, "If you buy your camera and Tx seperately the plug polarity and voltages may be very different." Thank goodness when the jack was plugged into the camera and power applied it did not smoke the video board.el cuarto que pido. seria deseable unas antenas de polarizacion circularWired Backwards!!!
Have not had a chance to fly with this yet. Tested with the extra camera that came with it did not work. I looked closely and found out the plug that goes in the camera is (Wired Backwards)! I slipped the wires out of the connector and put them in the right order. Blammm Fixed...
Looks like it would be easy to remove Tx heatsink for other applications (void warrenty). Having a problem finding a small Antenna for the 330 Quad... Might have to save this for a 450 Quad I will be building next...
Just got this unit it came with a ERO plug no problem
cut off lead hooked up 12 v battery all channels work everything lights up BUT PICK think cam is bad used a smaller one i had work ok
have a back up cam on order hope its ok when it gets heR
SORRY HK BUT LOOKS GREAT BUT HAVE TO RATE IT LOWERUsed this in a Bixler with an old Optic 6 radio and a patch antenna. On my 9th flight out around three and a half miles, I lost control of the plane. Video was working till I dropped behind some hills. I dont think I would push the video much more than that. I'm now going to UHF and better OSD (return Home) so I will write another review later. Happy FPVing:)Mine was Doa
there are no instructions or paperwork with any specs, there isn't even any specs on the equipment itself.
I feel like I was scammed!I tried today in a 30cc gas plane...plane it didnt work well...
it crashed my 2.4 Jr 12x radio.... i tried in the field and detected the problem before flying...on the next time i will try a 72Mhz old style radio...Good product. I haven't tested it so much yet but when I going to test it next i going to put the antenna up in the air too get more range. Use 3 cell batteries to power reciver and transmitter.Works well, however on a gas (this doesn't occur with nitro) vehicle, the picture disappears at certain RPMs; also if the antennas are close enough, this system, although on a very different band, will disrupt a 2.4ghz signal to the point of signal loss almost instantaneous.i was very pleased! i plugged it into my laptop to fly it worked great ! one of the solders came lose on the wire harness but all else its great ! check out my video here http://www.youtube.com/watch?v=idEgOSDK4Ks