Total Price

$0.00

Cart 0 Cart 0 Loading...

Corona CS238HV Analog Metal Gear Servo 4.6kg / 0.13sec / 22g

Generating Links

Corona CS238HV Analog Metal Gear Servo 4.6kg / 0.13sec / 22g

Already Purchased Discontinued Product

Please continue searching for a similar product.
SKU:
014000034-0
want FREE shipping? Click here to find out more!

Corona CS238HV Analog Metal Gear Servo 4.6kg / 0.13sec / 22g

 

Specs:
Model: CS238HV
Operating Voltage: 6.0V / 7.4V
Operating Current: 300mA / 400mA
Operating Speed: 0.14sec.60°/ 0.13sec.60°
Stall Torque: 4kg.cm / 4.6kg.cm
Size: 29X13X30mm
Weight: 22g
Dead Band: ≤5uSec
Operating Travel: 40°/one side pulse traveling 400us
Potentiometer: 3 slider/Indirect Drive
Ball bearing: MR106
Gear: Metal
Motor: Coreless
Spline count: 25
Connector wire: 215mm
Operating Temperature Range: -20°C ~ +60°C

  • Servo Torque(kg)(min. 0.01kg) 4.60
  • Servo Speed (Sec/60deg) 0.13
  • Servo A(mm) 35.00
  • Servo B(mm) 29.00
  • Servo C(mm) 31.00
  • Servo D(mm) 13.00
  • Servo E(mm) 40.00
  • Servo F(mm) 20.00
attributeset-11
Close

Dimension Diagram Guide

  • attributeset-11

Close

Upload video

Only registered users can upload video. Please, log in or register

Topics
Sort by
Most Recent Topics
* Nickname:

* Your Reply:


Please, enter the text shown in the image into the field below
*Verification Code:
Cancel
Submit
Post a new Topic
* Nickname:

* Your Topic:



Please, enter the text shown in the image into the field below
*Verification Code:
Post Topic

Only registered users can write reviews. Please, sign in or sign up

John | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

May 19, 2016

These servos work just fine with my orange receiver and a 5 volt BEC.
The complaint I have is with the servo arms. They do not fit the metal out put shaft (spline) on the servo; the servo arm holes are too small. I had a few old arms from a full sized FMA servo and they seem to fit ok.

| Verified Buyer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

May 18, 2016

God og billig servo, momsen skal ned I DK foer vi gaar konkurs

Ashay | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

Sep 20, 2014

These servos are great for 50-60" plane currently my servos hooked in rudder and elevator. They r high performance servos according to their cost. In short they r worth the price.

Sooty | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

Aug 23, 2013

Sad to say I have come to the conclusion that these servos are not HV in a useable sense.
They might be HV in that they do not burn out after being connected to a 2s LIPO for 45 minutes but they develop a dose of frantic jitters at end of travel. Who wants their ailerons or elevator beating the air at full travel? This gradually decreases in intensity as the voltage is lowered. Even at 6v they are jittery to the point I would not use them.
Everything goes smooth, quiet, and stable at 5V and I would never use them at any higher voltage.
All 4 servos I purchased behave like any other standard, cheap, strong servo at 5v.
Forget the HV specification.

Sooty | Verified Buyer

  • Quality
  • Value
  • Overall

Customer Rated

Aug 21, 2013

Just received 4 of these little beasts. Hooked them up to one of my Orange Futaba FAAST compatible RX's and tried them at various voltage rates. I set the RX to analog mode - 3 slow flashes. Servos are wildly jittery on 2s 7.2v Lipo, extremely jittery on 6.4v LIFE, mildly jittery with BEC set to 6v and quite good with BEC jumper set for 5V.

So useable High Voltage they are NOT. I suspect the Orange RX can be a bit noisy so will try later with FrSky RX when one is available as I have had better smoother results with them.

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!