The FLIP32 AIO (all-in-one) Pro Version flight controller includes a Flip32, MinimOSD, 5V 3A UBEC supporting up to 6S, 90A current sensor, a MS5611 barometer and PDB all on a 35x35mm PCB with 30x30mm mounting holes.
This version of the Flip32 AIO uses improved components and design that will properly limit the voltage to the MinimOSD preventing voltage spike and damage to the OSD.
• STM103 MCU runs Cleanflight firmware
• 8PWM output, supports Octocopter
• MS5611 Barometer
• Only 35x35mm, mount holes 30x30mm
• Onboard USB (for config the OSD and FC)
• 5V 3A UBEC (2-6S)
• OSD hardware, Compatible with MinimOSD/MWOSD/CC3D OSD
• Small PDB
• Current and voltage sensors
• Better OSD Chip used with less power consumption
• 2x Software serial, 2x Hardware serial ports
** This version ONLY Supports SPPM and Serial RX, an external SBUS inverter is needed.
Dimensions: 35 x 35 mm (30 x 30mm mounting holes)
Weight: 17g including wiring
Flip 32 AIO Flight Controller
Using Turnigy 9x don't have SBUS but still bought it. Its a good flight controller. Checked on clean flight, looks fun.If you can grab this little board on sale for 10 USD or less, it is absolutely fantastic! First thing you should do is load betaflight to it, and by the way, this is a naze board, not a flip. Second thing you should do is load scarab osd. After that you will need to calibrate the current and voltage sensors, because the default values are way off. Finally, you will need an Sbus inverter and to change the power pad for serial port 2 if you want to use an Sbus receiver. After that, this is actually a very capable board, if a little outdated because of the F1 chip. Still flies very well (once tuned of course), and the included current sensor + OSD are excellent features at this price point. My only real gripe is the lack of native Sbus support, and the janky PDB, use an external one instead.Because of the F1 chip, it's outdated for multicopters.
Does not connect to the most recent cleanflight software!
To get it working, I had to download cleanflight configurator v1 .crx file, enable developer mode on chrome, and install the .crx file manually.
I'm using Silicon labs drivers for usb/uart/vcp.
After all that, it's really quite a nice chip!Be aware that you cannot use the 5v from side of bord to supply the receiver it simple dont work i have 6 of them and all do the same.
I use separate PDB, in these way i dont have lines in video i dont think it has LC filter
Hard to solder all the wires from esc - on a side and + on the other side.
Use a case or epoxy to protect the chip.
Update with Naze otherwise it stay stuck in bootloader.
Its a good deal!Thank you HK!
I allready start to build my 7 th drone.
Keep making great offers!Just a quick follow up on my review..Updated to 1.14.2 and voila Altitude hold now solid..Did not touch any pids on anything...It seems that previous firmware (1.14.0 ) first one after 1.13.0 in Cleanflight had a bug...After research, I flashed board again to latest in the 1.14 list (Stable) and same configuration on quad and results where fantastic...No more changes...VERY HAPPY with this board. Also for those of you wondering PPM only or the other BUS thing...No PWM..in case some wonder..Also camera stab works great..Just know that pin 1 and 2( previously motor 1 and 2 are now for servo tilt or roll or in my case controlling brushless gimbal with switch (up or down) PINS 3456 are now your motor outputs (1234=3456 in that order..Meaning pin 3 is motor 1, and so on. Hope this helps you guys.This is the 4 th FC it was on sale 9 euro.
Now i regret i didnt bought more, new price 33 euro.
THX HK!Bought 3 of these boards...Outstanding, set them up using Cleanflight conf 1.2.4 as I already had used it to set up my Illuminaty 32 boards with great success.Running standard PID'S it flew well (S500 with LD POWER 300-1 motors from H.King) after that I slightly lowered P to 33 I to 20 and D to 0 and solid..I film so my settings are for 500 and 450 quads..works great for me...I use PPM only...Barometer works well..Lowered VEL down to 80 and ALT to 25 and D 5..Works well and holds (no wind filming)...I have noticed thru research that PID numbers people give are subject to what type of Configurator you use..On 1.2.4 Cleanflight Rates are basic numbers...Using latest 2.0.3 decimals where added thus more confusing...so I opted to work with configurator that I understand...Why not leave things alone...Overall excellent value and results for me.Good luck guys ( also use firmware 1.14.0 Older but very workable on this board..Yes I did try latest 2.0.3 and not for me ...My numbers didn't translate PIDS from 1.13 and 1.14...1.13 does not work on this board..(it does on ILLUMINATY 32 very well)I bought 3 pcs.
First one i break the usb port (no big deal, i can Connect with stmd adaptor).
The rest i use epoxy for protection.
As the title said all in one.
Bought one which had a bad connector for the USB port but since I had built my quad according to the positions of the fc's connectors I decided to order a new one. Then I flashed the new fc with the latest firmware, built it to look like my own, ordered an sbus inverter, got it finally working and then - I can't fucking arm the motors. Not by a switch nor a stick command.
Worked with it hours and hours, read all about like everything on the forums and still couldn't get it functioning. Now I'm pretty done with this fc and already ordered another one, a SPRacing F3 EVO. This was my last clone of NAZE32.
In addition, the manual coming with the fc tells you where to connect stuff but if you encounter some problems with connectivity there's no place you can find solutions.