New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

GWS V-Tail Mixer II (200 step)

GWS V-Tail Mixer II (200 step)

Discontinued Product

Please continue searching for a similar product.
SKU:
GW-V-TAIL-J
WANT FREE SHIPPING? Click here to find out more!

This device allows mixing any channel to other channels and making your aircraft easier to fly.
It is necessary for you to fly the Delta Wing or V-Tail airplane if the transmitter has no mixing control function.

Operating voltage : 4.8V~6V (typical 4.8V)
Resolution : 200 steps
Working Temperature : -5°C~50°C
Weight : 5 g
Dimension : 22x13 mm  (0.866x0.512 in)
Mixing rate: 1 : 1

Directions;
Plug the AILE and ELEV connector into the receiver aileron and elevator channels respectively as the wiring diagram shown.
Connect the AILE and ELEV control servos to SERVO 1 & SERVO 2 of the V-tail mixer in accordance with the wiring diagram.
Do not get wet on the V-tail mixer.
Any Modification will void warranty at owners risk.

  • SKU GW-V-TAIL-J
  • Brand -
  • Capacity (mAh) -
  • Shipping Weight 40.0000
  • Length 0.00
  • Width 0.00
  • Height 0.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Use for differential throttle with only one additional tx mix. With flip of designated tx switch I have dif. throttle for water taxi...turn off mix and have conventional rudder for flying. Ordering more for future multi-motor flying boats.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Use for differential throttle with only one additional tx mix. With flip of designated tx switch I have dif. throttle for water taxi...turn off mix and have conventional rudder for flying. Ordering more for future multi-motor flying boats.

One of the best v tail mixers

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

One of the best v tail mixers

I bought this V-tail mixer as a replacement for the Turnigy V-tail mixers I bought earlier, but which gave a lot of jitter on my TowerPro miniservos. This one does not give jitter at all, instead nice and smooth movements and a neat position hold.



The leads to the receiver on this mixer are very short, only 5-8cm long. This in contrast to the 20cm or so leads of the turnigy. See for yourself if that's a con or a pro, for my application it was a definite pro as space is pretty limited in a 22cm boat.

A little pricey, but the superior performance justifies the extra cost just fine IMHO.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought this V-tail mixer as a replacement for the Turnigy V-tail mixers I bought earlier, but which gave a lot of jitter on my TowerPro miniservos. This one does not give jitter at all, instead nice and smooth movements and a neat position hold.



The leads to the receiver on this mixer are very short, only 5-8cm long. This in contrast to the 20cm or so leads of the turnigy. See for yourself if that's a con or a pro, for my application it was a definite pro as space is pretty limited in a 22cm boat.

A little pricey, but the superior performance justifies the extra cost just fine IMHO.

I got this to try out in one of the kids toys, a foam model the Hyper Flyer

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I got this to try out in one of the kids toys, a foam model the Hyper Flyer

doesn't work as a V-tail mixer. Strangely, it will mix any two channels together, except for elevator and rudder. I can mix Elevator, Flaperon, "Throttlevator" etc. etc. but when I mix the two channels that you would normally expect from a "V-tail Mixer" (as the package describes it) it barely moves the servos at all. I've tried it with two transmitters and 3 receivers, plus the APM, always with the same result!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

doesn't work as a V-tail mixer. Strangely, it will mix any two channels together, except for elevator and rudder. I can mix Elevator, Flaperon, "Throttlevator" etc. etc. but when I mix the two channels that you would normally expect from a "V-tail Mixer" (as the package describes it) it barely moves the servos at all. I've tried it with two transmitters and 3 receivers, plus the APM, always with the same result!

only for v- tail not for delta

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

only for v- tail not for delta

Hmm. Eip nit moittia voi. 3kpl kytss ja moitteetta toimii

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Hmm. Eip nit moittia voi. 3kpl kytss ja moitteetta toimii

Voici une utilisation particulire de ce produit, jutilise celui-ci sur un bimoteur afin de rgler la vitesse des moteurs avec la direction.



Here is a particular use of this product, I use it on a twin-engine to adjust the motor speed with rudder.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Voici une utilisation particulire de ce produit, jutilise celui-ci sur un bimoteur afin de rgler la vitesse des moteurs avec la direction.



Here is a particular use of this product, I use it on a twin-engine to adjust the motor speed with rudder.

What for is this, if you have a mixer in your radio?

Now, I will tell you, why I use it istead of the radio mixer. This cheap thing makes it possible to use a gyro on both servos lets say on the ailerons. If you put the giro in front of that mixer on the aileron channel, both servos will act onthe giro as the input channels allway work on both servos. Same is possible but not common on elevator. If you have your mixer in the transmitter used, you could put a giro only on one servo, acting only on one of the two ailerons wich makes not really good work. With this very light weight part, there is a great solution to do that. Thats why I use his instead of my transmitter mixer on a small Elevon jet.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

What for is this, if you have a mixer in your radio?

Now, I will tell you, why I use it istead of the radio mixer. This cheap thing makes it possible to use a gyro on both servos lets say on the ailerons. If you put the giro in front of that mixer on the aileron channel, both servos will act onthe giro as the input channels allway work on both servos. Same is possible but not common on elevator. If you have your mixer in the transmitter used, you could put a giro only on one servo, acting only on one of the two ailerons wich makes not really good work. With this very light weight part, there is a great solution to do that. Thats why I use his instead of my transmitter mixer on a small Elevon jet.

Great unit, I use it on a funjet ultra with a hobbyking T6A radio. Very small, light and tidy unit. Aileron and Elevator sockets are mislabelled, but once you get past that it works beautifully. Super smooth response, i believe it really is a 200 step mixer.
Highly recommend!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great unit, I use it on a funjet ultra with a hobbyking T6A radio. Very small, light and tidy unit. Aileron and Elevator sockets are mislabelled, but once you get past that it works beautifully. Super smooth response, i believe it really is a 200 step mixer.
Highly recommend!

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
Customer files
Connection diagram Download [6]
MAnual Download [112]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!