The H550 V1 is a well thought out 550mm hexcopter frame built from quality materials. The main frame is glass fiber while the arms are constructed from ultra durable polyamide nylon.
Assembly is a breeze with pre-threaded brass sleeves for all of the frame bolts, so no lock-nuts are required. It utilizes one size of bolt for the entire build, making the hardware very easy to keep in order and only requiring one size of hex wrench to assemble.
The added lift capacity of a hex configuration makes this frame ideal for carrying larger payloads such as camera systems and other electronic components. This makes for an exceptional camera rig or simply a very agile and powerful multi-rotor frame for aerobatics!
The H550 also features colored arms (3 white and 3 red) which are great for orientation. It helps to keep you flying the right direction without the need for different colored props.
We offer a full line of multi-rotor electronics such as multi-rotor control board, ESC & motors. It has never been easier or more affordable to get a quad in the air!
Built from quality glass fiber and polyamide nylon.
Pre-threaded brass sleeves for all of the frame bolts.
Colored arms for orientation to keep you flying in the right direction.
Large mounting tabs on main frame bottom plate for easy camera mounting.
Ideal for carrying larger payloads such as camera systems and other electronic components.
Weight: 460g (w/out electronics)
Motor Mount Bolt Holes: 16/19mm
6 x 28mm 1000~1200kv (or similar size/kv)
6 x 15~25 Amp ESC
6 x 8x4~10x4.5 Prop (3CW & 3CCW)
1 x HobbyKing Multi-Rotor Control Board
1 x 2200~3000mAh 3s 11.1v Lipoly Battery
First thing I noticed out of the box is the arms are not bright red, they are maroon/purple and the white ones are more off-white, not that it really matters but definitely doesn't look as clean as the one pictured, this could be a one off run perhaps with bad colours. The arms seem a little flexible on the twist axis, would shouldn't be a show stopper if motors and props are balanced. Otherwise it fits together well, at first I thought the screw holes were not quite lined up but if you start all the screws before fully tightening it comes together really well. As with most HK hardware, if you have a good quality set of hex drivers and don't over tighten the screws are fine. The edges of plates are sharp and will cause problems with wires so best to sand those down a bit with a dremel or something and seal the edges with CA. After saying all of that we are talking about a mere $20 frame kit, which is amazing value when you think $20 bucks barely buys dinner these days. 4 stars instead of 5 only because the colours don't match :)Nice Frame. The colours of the arms are not pretty, but for 20$ is that OK. Cheap and nice Frame for easy building of the Hexacopter.
I did and I'm happy with. Resistant plastic, low cost replacement ans compatibility to the 450 size quadframe. Some seconds Video of my copter here
<object width="300" height="169"><param name="movie" value="//www.youtube.com/v/l_3gYlmv8Rw?hl=de_DE&version=3"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="//www.youtube.com/v/l_3gYlmv8Rw?hl=de_DE&version=3" type="application/x-shockwave-flash" width="300" height="169" allowscriptaccess="always" allowfullscreen="true"></embed></object>
In erster Linie ist es ein gutes Produkt.
Es erfllt Sinn und Zweck zu einem guten Preis.
ABER: In der Artikelbeschreibung sind die weien Arme wei und die roten Arme richtig ordentlich rot. Die Realitt sieht da leider anders aus. Die weien Arme sind traurig grulich und die roten Arme sind sehr dunkelbraun. Absolut hsslich kann man nur sagen!
Das sollte unbedigt gendert werden. Es kommt einem vor, als wrde alles aus willkrlich zusammengemischten Recyclingresten mit zu wenig Farbstoff bestehen.
Sehr enttuschend.Very strong arms. I use it for spares in my dead cat.good quality but the arms are brown and white!Nice Frame, decent quality.
Cheap cheap cheap and easy to build and fairly rigid can put all your stuff in it and place the lipo on topKit from the europan warehouse was delievered whit brown arms. Perhaps it is an joke for german buyers (if you understand, what i mean) 8-)))) lol. The quality itself is acceptable, but not great - okay for the pricenice and cheap kit that does nto have too much flex, also good for spare arms as arms are not sold separatelyquality is ok for the price nice for spare part in case of crash for 3D fly ^^