Standard 10A car esc with forward reverse and a good range of features such as timing adjust and breaking. Supports a wide range of motors. Very reliable!
Full protection feature including low voltage, over-heat, throttle signal lost, startup
protection and self-check.
Compatible with sensorless brushless motor.
Excellent startup performance, linear and quick throttle response.
Supports highest motor speed 240,000RPM(2 poles), 80,000RPM(6 poles) and 40,000(12 poles).
Easy to configure with program card.
System can automatically detect throttle neutral point, and neutral range is adjustable.
Three work modes for different environments.
4 step reverse force adjustment
5 step start force adjustment.
3 step brake force adjustment
5 step drag brake force adjustment,
4 step initial brake force adjustment.
Input voltage: 1-2S Lithium batteries / 3~8 Ni-xx
Cont. Current: 10A
BEC output: 1A/5V (Linear)
Size( length X width X high): 22x17x7mm
I was sick of the issues I was have with my genuine Micro T so I swapped it out for this one and the results are fantastic, much smaller, more tuning options and way smoother than the original. Highly recommended as a cheap upgrade for your Micro T.Work with arduino. Perfect for micro robot.Good little ESC. Quick to go between forward and reverse - a good upgrade for the losi micro range of carslittle devil it is. Works fine on small selfprinted (3D) car. LIKEWorks great in a losi micro crawler. I have it paired with a single and two cell and the 4500kv motor from hobbyking. Killer mix and nothing gets hot at all. Easy to use and amazing performance.I just got a couple of these for an RC boat project (a micro 3D printed tug).
Programmed it with the "HKProg-card". Hooked it to a 16g hextronik 1700kv outrunner on one end and a 1S 1200mah round nanotech LiPo on the other end. Works great. Motor start is surprisingly smooth and throttle response is very linear. I assume the bad reviews were defective items.
Overall It looks like it is going to fit my needs.
Note: no connectors on either the battery or the motor side. Comes with a standard size servo plug though.this is one bad little esc !!! ive got it on my losi micro truggy with a 2s lipo and it will fly know !!!ideal for the micro car 1cellIch habe den Regler fr das Sumpfboot Swamp Dawg gekauft funktioniert sehr gut und ist sehr gnstig. Auch wenn auf dem Bild es so aussieht als ob nur Brushed Moteren gehen, das stimmt nicht es geht Brushless.
Da hat Hobbyking ein falsches Foto reingestellt.
Es sind KEINE Stecker dran diese mssen dazu gekauft werden.I also recently purchased this esc it is great I have installed this esc on a losi micro rally with the large pinion on 2s Turnigy nano-tech 180mah 2S 25~40C Lipo Pack with a turnigy 4500kv and a VSD-6 servo this combo works great the motor plat will need to be modified in order to install this motor on the stock motor plate but was simple and easy the servo fits easy but is a little to small though so I used double sided tape to secure it in place servo tape would have worked better, this esc and motor combo on 2s will also work great on a losi micro dt/raminator/high roller/t/Baja with the large pinion you will also need to modify the motor plate in order to install this motor. thanks hobbyking for the great products. motor temps are always cool and same with this esc I get about 20 min run times with the 2s I mentioned befor.
No File Name download now [227kb] No File Name download now [227kb] esc10a 3V-13V download now [101kb] User manual download now [430kb] Inside Micro T download now [2.90Mb] CXC-10A compared to Xcelrion download now [2.58Mb]