Holybro Kakute F4 A10 V2 Flight Controller with OSD and BMP280 Barometer
Holybro Kakute F4 A10 V2 Flight Controller with OSD and BMP280 Barometer
Copy and Share the Below URL
Accessories
The Holybro Kakute F4 A10 Version 2 is the next generation of this popular flight controller. New features over the original F4 A10 are, additional UART's (UART 4-5), through hole solder pads, BMP280 barometer, low profile and a 12C pad available for certain external sensors.
It still has all the popular features of the original FC such as an OSD (on screen display) and a 120amp PDB (power distribution board) integrated into the same package and with it's low profile it makes it very simple and convenient to build a racing drone. The F4 A10 V2 flight controller has a STM32F405RGT6 32-bit processor for extra processing speed and a ICM20689 (SPI) IMU gyro/accelerometer. This running at upto 32kHz mounted on vibration-isolating foam so there is no need to soft mount the board itself. It also still has the dedicated bootloader button which makes firmware flashing a breeze and the OSD interface is highly customizable and can be setup and fine tuned to your personal requirements. There is an onboard blackbox with 128MB Dataflash chip for all your data logging needs.
No more pin headers to get in the way as all wiring is soldered straight to the board to reinforced, gold-plated solder pads for trouble free soldering. Input voltage is for 7V to 42V which allows the board to be powered directly from a 6S battery pack, PDB maximum continuous current is 120A. The FC also has a filtered voltage output of 5V 1.5A and 3.3V 200mA to power peripherals such as GPS, RX, FPV camera or LED strips. 5v/3.3v RX selectable.
The FC supports Betaflight (pre-loaded) and Cleanflight, also supports BLHeli pass through for easy ESC upgrade and configuration. The latest version of the Kakute AIO F4 with OSD, barometer and blackbox is one of the best low profile flight controllers available today for your racing drone.
Features:
• STM32F405RGT6 32-bit processor
• ICM20689 (SPI) Gyro/Accelerometer
• 128MB Dataflash chip for Blackbox logging
• Betaflight OSD (on screen display)
• Dedicated bootloader button for easy firmware flashing
• Separate USB VCP driver
• High quality, gold plated PCB
• Built in soft mounting
• 120A PDB (power distribution board)
• Micro USB connector for programming
• High voltage input, 7 to 42V (up to 6S)
• Automatic voltage monitoring
• Filtered voltage output for noise free clean video
• Supports Betaflight and Cleanflight
• BLHeli flashing supported by hardware
• Low profile design
Specs:
MCU: STM32F405RGT6 32-bit processor
IMU: ICM20689 (SPI)
Barometer: BMP280
USB VCP Driver: Separate from UART's, usable simultaneously with all UART's
UART's: 5 (UART 1, 3, 4, 5, 6)
Receivers: Supports SBUS, iBus, Spektrum, Crossfire only, PPM and PWM receivers are not supported
Logging: 128 Mbit Dataflash chip for Blackbox logging
Dimensions: 35 x 43 x 7mm (Inc USB)
Mounting Holes: 30.5 x 30.5mm
Weight: 7g
Please note: A copy of the instruction manual is available under the "Files" tab below.
Sonny | Verified Buyer
-
Overall
-
Quality
-
Value
QC Issues
Mar 07, 2019
Viktor | Verified Buyer
-
Overall
-
Quality
-
Value
Great
Jan 26, 2019
Tim | Verified Buyer
-
Overall
-
Quality
-
Value
Full featured AIO Flight Controller
Oct 14, 2018
Marian | Verified Buyer
-
Overall
-
Quality
-
Value
Great flight controller
Jul 16, 2018
Instruction manual | Download [6] |
Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!