Look no further for the ultimate in durability and power in mini quad motor. The new Multistar Elite 2306 2150KV MINI MONSTER is here
The Elite 2306~2150kv is dubbed the MINI MONSTER, producing nearly 1000g of thrust on a 6inch prop and 4s (each). The Monster is like no other mini motor on the market it was built around a 4mm main shaft… that’s correct 4mm, and massive 11mm EZO japan bearings! The thicker bell added efficiency and durability. The single wire wound stator can deal with the high amps and heat much better the multi-strand. The replaceable 5mm prop adapter increases its survivability in a hard hitting crash. The Mini Monster with the 4mm main shaft with 11mm bearings, thick bell, single wire wound makes this the most durable MINI quad motor around.
Multistar Elite motors are more than a fancy name and new dark green color.. Built using the highest quality components from Japan bearings, N45SH magnets, .2mm laminations, 180deg oxygen free copper wire, .005g balancing, perfect wind laid down and 100% QC, and then the design of each motor are also evaluated for their type application and everything from their mounting, to the prop type adapters are taken into consideration. The Elite motors are truly works of art
Multistar Elite is unmatched in quality and value, and the performance speaks for its self.
• 4mm main shaft with 11mm bearings
• EZO Japan Bearings
• N45SH Magnets
• 0.2mm Laminations
• 180deg oxygen free single strand Copper wire
• 0.005g Or better balancing
• Perfect lay down windings
• 100% QC
• Replaceable CW prop adapter
Lipo cells: 2~4s
Max Amps: 20A
Dimensions(Dia.xL): 23 x 6mm
Motor Shaft: 4mm (5mm prop shaft)
Prop shaft: 5mm or Direct mount with 9mm center to center
Bolt hole spacing: 16mm * 19mm
Connectors: 2mm bullet
1 x Multistar 2306 - 2150KV motor (CCW) and prop adapter.
Max Currents (A)
Length B (mm):
Can Length D(mm)
Unit Weight (g):
Total Length E(mm)
I used these motors on Foam planes to get small powerful motors that were fast. This motor Achieved everything I wanted and More. It will Spin a 5050 3 blade just fine, although the bells will get warm when running hard on 4S. Pay attention to what batteries you are running and make sure the are of enough C rating as these motors do pull a lot of current, and could puff your batteries. I would run a 25A minimum ESC for this motor.Muito pequeno e leve para a força que tem. Recomendo-o para quad e tri 250.These are the biggest pieces of crap I have ever owned. I have gone through 3 of these motors and 5 esc's because of the motors. The bells are lopsided and don't let the motors turn smoothly, and as a result draw excess power and blow my 30A max esc. I have wasted more time and money on these than any motor is worth.power house and smooth. I have them on a HK color 250 (needed 3 mods to fit clean, shaved top of arms back to first slot so wires didn't rub motor can, opened 2 of the small holes to get screws in motor so wires lined up with arms, and enlarged center hole for clip on bottom of motor). I didn't get an amp reading on my data logger with the 2 blade 5050 props on 3s because an ESC shut down and it crashed. New frame and 2 blade 5045s on 3s produced an amp draw of 58.4 amps on the data logger. With 5050s the quad acted at least as fast as my other HK color 250, 1806-2300kv motors on 4s. These motors are truly beasts, I love them motors but will be getting bigger ESCs for them. 20amp would be minimum if not higher.Motor duro y potente. Perfecto para drones de carreras. En 4S tienen una aceleracion brutal.Very nice motors. Durable and powerful.
Only downside is replaceable 5mm prop adapter, where do i get it??Work well in my racing quad. I even mixed them with 4 mini beast motors and they worked just fine. I used this as well