The OrangeRX DSMX/DSM2 compatible 2.4Ghz transmitter module offers a simple and convenient way to utilize your module-based Futaba compatible transmitter with DSMX/DSM2 compatible receivers. Simply replace your stock module with this and you are ready to bind to any DSMX/DSM2 compatible receiver.
• 100% Futaba compatible (works with any Futaba compatible module-based transmitter)
• 4 operating modes: DSM2 1024/22ms, DSM2 2048/11ms, DSMX 22ms, DSMX 11ms
• Easy to access bind button
• Range check mode
Compatibility: All Futaba 5 pin module-based transmitters
2.4Ghz protocol: DSMX/DSM2
Voltage input: 6~15VDC
Range: Full range system
OrangeRX DSMX/DSM2 compatibele 2.4Ghz transmitter module (Futaba compatible)
RX bind plug
Module uses a unique Global ID for binding. In case of binding issues with other branded receivers press the "Change ID" button on module to change the Module ID to another unique value reserved for that module (5 ID's assigned to each module).
There are over 4 billion unique ID's assigned to OrangeRx modules.
1) This is not a Spektrum DSM2/X product, nor is it a copy of a Spektrum DSM2/X product. The Spektrum and DSM2/X brand is a trademark of Horizon Hobbies USA.
2) This is not an underground black market fake Spektrum product. OrangeRx quality is guaranteed.
- Blade Count:
I ordered wrong one , i needed JR
Egy Futaba 3PK-hoz rendeltem egy ismerosmnek. n a sajtomhoz rgebben Corona modult hasznltam, de remljk ez is j lesz.
i recieved 3 recievers and the orange module for futaba im using a futaba t9cp the reboot time of the recievers is a bit slow but so far i have hade no issues with them,im soon going to use one on a 250 fpv racing quad so ill keep you posted on range ,reliability etc ,so far so good ,nice products hk
I purchased this in hopes to utilize an older module based 8U Futaba transmitter. When installed the module worked excellent and was able to bind to both Orange Rx and Spektrum receivers. The only issue I have is that the channel sequencing on the transmitter is different than the sequencing in the receivers. Normally this would not be an issue as you would just connect the ailerons to whatever channel responds to the aileron control input. However when using a RX3S OrangeRX receiver the control surfaces are preassigned to a particular channel sequence. Unless your transmitter is able to reassign the channels you will not be able to use this with a stabilization receiver. The only way I can see to overcome this would be to use a standard Non-Stabilized receiver and then add the RX3S separately using the RS3X stabilization unit without a receiver. All things considered I am very happy with the unit. The little issue I have is a transmitter channel sequencing issue and not a module issue.
I have a 9Z Futaba that is still a great transmitter. I thought Id revive it with a Frysky module and that did not support the frame rate so got this to replace it. I have had several flights over the past few weeks since I had got it and all have been without a glitch till just now. It was browning out in flight. Id lose all control then regain it. This is on a cheap HK Foamy. As I attempted to land it browned out and crashed. Glued it back together and refreshed the bind and all seemed well in the workshop. Took it back out to give it a run and once again it crashed. I don't know why this is giving me grief all I know is that my Futaba FAAST has never once glitched. I cant be stuffed with the risk of this cheap crap anymore and will stick with brands I know work all the time every time.
No doubt about the price savings of this module compared with others, however I have some issues. I was using an FrSky module in my Hitec Optic 6 but saw the ORX receivers with Gyro built in and couldn't resist, plus the DSM2 option opens up the whole BNF market. Duly bought TX module and V3 RX with Gyro, but could not get it to work properly even with my simple foamie glider as I wanted to control the 2 ailerons separately and have aileron differential or flaperons. The two aileron servos seemed to defeat it. So then purchased the USB updater, waited (again), and reprogrammed from AETR (Futaba/Hitec) to TAER. Still could not get Gyro to work on both ailerons and have differential... HK answer was that Gyro on one aileron should still work, can't do anything else. I know this is picky but, it's almost as if the person designing it doesn't know what flyers might want. I won't be buying another RX until there is an update and I know that there are actually two separate (not one copied from the other) aileron channels. Plus the AUX control does not work for me, and I have bits of elastic band to hold the TX module clips open so it stays in place and does not rattle!
This really works, but you'll need to do the firmware update to convert Futaba's channel assignment to DMS2. Excellent Range also.
eccellente con le radio turnigy prende anche le spektrum
Just so you all know
THIS IS AN AIR MODULE, IT ONLY WORKS WITH AIR RECEIVERS, IT WILL NOT WORK WITH LAND MODULES, EVEN THE ORANGE LAND 3 CHANNEL MODULE.
Module tested in a Futaba 9z and works great, Tested in a Futaba 3pk and does not work at all although I have not tested it with an air receiver yet.
100pcnt Futaba compatible (works with any Futaba compatible module-based transmitter)
NOT ENTIRELY TRUE
Be sure to order the programming card to remap the module for Futaba radios, otherwise ARFs with Spectrum receivers with stability will not work correctly. Just moving the servo wires around will result in stability being on the wrong control surfaces. US store sells the module but not the programing card, have to go to Asian store, and I've been waiting for over 35 days now.
ORX 2.4GHz Transmitter Module Manual.pdf download now [404kb] Instalation in Futaba T10 download now [193kb] Users manual download now [2748kb] Module Pin Layouts download now [210kb] instalation to Aurora9 download now [67kb] No File Name download now [1202kb] No File Name download now [67kb] wrong instalation to Aurora 9 download now [67kb] No File Name download now [28kb] Aurora9/DSM dual Umbau download now [1534kb] HK Futaba Module download now [963kb]