Total Price

$0.00

Cart 0 Cart 0 Loading...

Race 32 Racing Flight Controller F303 (Deluxe)

Generating Links

Race 32 Racing Flight Controller F303 (Deluxe)

Price:

Now save save $16.53 $16.53

Special Price $25.89 $25.89

You save save $16.53 $16.53

Was  $42.42

QTY:
Shipped From:
  • USA
Already Purchased
Status:
In Stock
SKU:
387000090-0
want FREE shipping? Click here to find out more!

First across the finish line for both performance and price and now just waiting for you to take the chequered flag!  The Race32 Flight Controller has been developed for quad racers where a light weight full function flight controller can give you the edge you need.

Fully compatible with Cleanflight the Race 32 FC has all of the major features of the latest boards including the fantastic STM32 F3 processor.  The faster ARM-Cortex M4 core has a floating point hardware unit for efficient flight calculations and loop times are twice as fast as previous generation STM2 F1 boards. 

Packed full of features the Race32 is the smart choice flight controller for the serious quad/multirotor pilot.

Features:
• Hybrid plug setup, JST plugs and through holes for pin connectors.  No compromise on ports. Full feature support of all modules, all at the same time.
• Protective case
• Stackable design - perfect for integrating with OSDs and power distribution boards
• Black Box Flight log recorder
• Next generation STM32 F3 processor with faster ARM-Cortex M4 core with floating point hardware unit.
• Plugs located on the same side of the board
•4 PWM 3 pin through holes connectors for ESCs, servos. Full support for Oneshot ESC's
• Supports SBus, SumH, SumD, Spektrum 1024/2048, XBus, PPM, PWM receivers. 
• Built-in inverters
• Dedicated output for programmable LEDs
• Battery monitoring port, buzzer port
• PWR ports for voltage and current
• Sonar support for precision low altitude position hold
• Barometer mounted on the bottom of the board for easy wind isolation
• Configuration of the flight controller via a cross-platform GUI (windows/OSX/Linux)
• Supports fixed wing, tricopters, quadcopters, hexacopters, octocopters and more.

Specs:
Dimensions: 36 x 36mm board with 30.5mm mounting holes
Weight:  5g
CPU: STM32F303 with FPU 256k flash
Gyro: MPU6050
Barometer: MS5611
Magnetometer: HMC5983
Ports: UART1/OSD, UART2/GPS, UART3/Serial RX,I2C

 

Upload video

Only registered users can upload video. Please, log in or register

Topics
Sort by
Most Recent Topics
* Nickname:

* Your Reply:


Please, enter the text shown in the image into the field below
*Verification Code:
Cancel
Submit
Post a new Topic
* Nickname:

* Your Topic:



Please, enter the text shown in the image into the field below
*Verification Code:
Post Topic

Only registered users can write reviews. Please, sign in or sign up

SHELDON | Verified Buyer

  • Quality
  • Overall
  • Value

works perfectly

Mar 19, 2022

good product good name difficult, to use at first .solved problems on u-tube and cheap.

robert | Verified Buyer

  • Quality
  • Overall
  • Value

Great FC with plugs so no soldering

Feb 11, 2021

Shame this is discontinued, get one if you can, load with inav and put a gps on and its rock solid. You have to remove from the case and short out the jp2 pads, then plug in the usb and run the inav configurator. When flashing the bar changes from blue to red and states 'error'. But disconnect and re plug in to usb and run configurator, all is fine.There is an instruction sheet which shows the board and all its connections. The holybro nano gps was virtually plug and play as was the BN220. The Holybro has an onboard compass so you have to sever the connection on JP1. You can do this by using the edge of a stanley blade. If you use the BN220 gps, that has no compass and was truely plug and play. Obviously configuring it in inav is another thing but plenty of documentation/ videos on the net. I like the plugs, I wish more FC's had them. Pad it well, this board doesnt like much vibration.

Federico | Verified Buyer

  • Quality
  • Overall
  • Value

Works Fine

Jul 29, 2020

For updating firmware, I needed to unckeck "No reboot Sequence" and then I was able to flash it. It gives an error when "checking", but at that moment disconnect and reconnect the board and it is already flashed. For installing Betaflight, first update cleanflight to the latest for SPRACINGF3

Joe | Verified Buyer

  • Quality
  • Overall
  • Value

Great value

May 17, 2020

Voltage monitoring doesn't work correctly

Agostino | Verified Buyer

  • Quality
  • Overall
  • Value

ottimo prodotto

Apr 28, 2020

Un regolatore fantastico e acquistato ad un prezzo ottimo complimenti

Agostino | Verified Buyer

  • Overall
  • Value
  • Quality

Prodotto ottimo

Mar 12, 2020

Prodotto eccezionale un fly controller di tutto rispetto a un prezzo fantastico

Benjamin | Verified Buyer

  • Quality
  • Overall
  • Value

Never got to work. Definitely not for beginners.

Sep 23, 2019

Seems like more experienced users got it to work but I'm cutting my losses. Expect trial and error using bits of information from random reviews. I'm a beginner and would discourage other beginners from getting this FC.

robert | Verified Buyer

  • Overall
  • Value
  • Quality

Good FC but PWM map wrong from factory

Jun 10, 2019

Good board, special thanks to Bruno who worked out the correct PWM mapping. If you are seeing the aux channels moving instead of the AETR channels in cleanflight, remap in CLI mode as follows - map AE34TR12 dont forget to save. Thanks to Bruno who stopped me throwing this FC in the bin.

Dany | Verified Buyer

  • Overall
  • Value
  • Quality

deff

Mar 19, 2018

flashen with ????

| Verified Buyer

  • Quality
  • Value
  • Overall

Certified Buyer Rated

Aug 09, 2016

A good one if you have to build with the small white connectors

  1. 1
  2. 2
Customer files
Manual A Download [141]
Manual B Download [158]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!