The RMILEC TS4047 10CH 2.5W UHF Module System offers the ultimate in range for your FPV model. It can be used with any JR style module transmitter. This package includes the TS4047 UHF transmitting module, RD4047P UHF 10CH receiver and all necessary hardware.
Included in box:
TS4047 transmitter module (JR style)
RD4047P 10CH receiver
Transmitter module antenna
All necessary hardware/wire leads
TS4047 Module Specifications:
Hardware frequency Range: 400MHz to 470MHz
Frequency stability: 2.5ppm
Output low-pass Filter: NONE
- Band 1
Frequency Range: 415Mhz-445Mhz
Step frequency: 480Khz
Channel : 70
- Band 2
Frequency Range: 433.05MHz -434.79MHz
Step frequency: 30Khz
Low Output Power: 30DB -31DB Peak (0.9W-1.2W)
High Output Power: 33DB -34DB Peak (1.9W-2.5W)
Low rate: 40Hz @10Kbps
High rate: 66Hz @15Kbps
RF interface impedance: 50 Ohm
Supply Voltage: 8.4V to 16V
Reverse battery protection: NONE
Logic Voltage: 3-12V
330mA/520mA (@50 Ohm load,12V Supply Voltage)
250mA/440mA (@No-load,12V Supply Voltage)
950mA/1.6A (@RF Short circuit,12V Supply Voltage)
Temperature: 50 to 70 Degrees Celsius
RD4047P Receiver Specifications:
Frequency Range: 400MHz to 470MHz
-112 DBM @0.1EBR(40Hz Refresh rate)(10Kbps low rate )
-111 DBM @0.1EBR(50Hz Refresh rate)
-110 DBM @0.1EBR(66Hz Refresh rate) (15Kbps high rate)
-108 DBM @0.1EBR(90Hz Refresh rate)
-104 DBM @0.1EBR(125Hz Refresh rate)
-104 DBM @0.1EBR(166Hz Refresh rate)
-101 DBM @0.1EBR(250Hz Refresh rate)
F/S turn on condition: >0.99EBR
Antenna gain: 2.15DBM
- Low rate mode
Refresh rate: 40Hz
Hopping rate: 40Hz
Hopping cycle: 13Hz
Recover time: 77mS
- High rate mode
Refresh rate: 66Hz
Hopping rate: 66Hz
Hopping cycle: 22Hz
Recover time: 45mS
Response Time: 4mS to 25mS
PWM Output accuracy: 0.5uS step ERROR<20PPM
PWM Output range: 0.5mS-2.5mS
PWM output cycle: 55Hz @Normal mode / 192Hz @Fast mode
PPM Output accuracy: 0.5uS step ERROR<20PPM
PPM Output range: 0.5mS-2.5mS Each channel
PPM output cycle:
50Hz@Normal mode & 1mS to 2mS Output
42Hz to 50Hz @Normal mode & 0.5mS to 2.5mS Output
50Hz to 83Hz @Fast mode & 1mS to 2mS Output
42Hz to 125Hz @Fast mode & 0.5mS to 2.5mS
PPM sync pulse width:
4mS to 16mS Automatic adjust @Normal mode / 4mS unchanging @Fast mode
RSSI output range: 0-3.3V (RF signal weak <0.8V)
Recommend Supply Voltage: 3.5V to 8.4V
Shutdown voltage: 3 V
Damage voltage: >15V
Reverse breakdown voltage: >-15V
Output ports withstand voltage: >12V
Normal Current: <60mA
Operating Temperature: –40 to +80 °C
Low frequency Power supply noise filter: Include
High frequency noise filter: Include
I really recommend this product, for me have work great, I had flown for more than 15kms away with 70-80pcnt RSSI. Don't listen what the other people say about this product, much of them haven't even used. 100pcnt recommendable.
IMPORTANT: there is many information and very useful upgrades in the internet, in the rcgroups RMILEC thread, like dipole antennas and other things, do it.
el tinc fa 6mesos i cap problema, fuciona molt be. cap pega a part del manual que no l'entenc gaire. pero lo basic funciona be. ficat amb una turnigy .9xr. un video de 1,2mhz i un raptor. cap perdua de senyal i cap problema.The nicest part about the RMILEC system is how nice the module fits in the JR radio. The system is also very easy to set up & bind. I have about 15 medium range flights on this system with no problems. I tested system with a spectrum analyzer & I found the 2nd harmonics to be in the 1.2 ghz range & it was very strong. Even with filters I would be afraid to use 1.2 ghz for video. The other thing that disapointed me was the freq. hopping was much less impressive than described! I tested 3 times with analyzer & it would only hop to 3 different channels. In short, very affordable system but I would steer clear of urban areas & don't use 1.2 or 1.3 ghz vid tx with this system. Overall good value if used properly! I also got 4 miles on ground radio range test.Hi guys!
I bought one 4 months ago and i am very happy with it!The only problem is that the module overheats and that is making me nervous.I found a sale in ebay with an aftermarket aluminum backplate i order one i put it on and now it runs cool!
Here is the ebay link
http://www.ebay.com/itm/251248653104?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649absolutely brilliant for the price. I have been 2.2km away from "launch" with this system controlling my Bixler 2, see my video in the videos section of this listing.
No glitches, no lockouts and it was a breeze to bind and re-bind. setting fail safe was trail and error but a bit of googleing sorted me out. Could do with having the fail safe procedure in the manual.
all in all, great bit of kit, and this JR version fits into my Turnigy 9x with no modifications whatsoever.Alguien sabe, como se configura el F/S ???
En el manual no pone nada.
El TX, tiene tres interruptores,tampoco pone nada en el manual, alguien sabe algo.Muito bom recomendo. Funciona muito bem com radio turnigy 9x
s precisa tirar a antena de 2.4. facil de bindar e com bastante alcance.
Ja voei a 4km sem ruidos. O f/S funciona muito bem mas no pode esquecer de habilitar a chave no modulo.This system works very well. I have a couple of pointers for anyone wanting to try it. 1) Always keep the rx antennas at 90 degress to each other, one vertical and one horizontal. 2)Keep the tx antenna vertical 3) dont sit too close to your video reciever with the tx as it will affect the video quality 4)Bind the rx with all equipment switched on vtx etc.
Good sytem and good price - nice one !Everyone is going to be disappointed when they find out that you can't use all ten channels without a ppm encoder board. You only have 8 usable channels as it comes from HK. Come on HK do your homework first. Where is the manual?This team of RX, TX is realmetne sensancional, I've flown over 4 km and only 20 meters from the ground and never any problems, I have it mounted on Turnigy 9x with fantastic software ER9x.