Silvia 70mm Composite EDF Jet (Kit)

• Overall
• Quality
• Value

Customer Rated

Aug 20, 2013

My setup:HK 10 blade edf,Maytech 70 A esc/bec,Zippy40C 3300mah. Bench tested at 62A and 840 watts. My AUW 42 ozs. Without plans I made a few mods. The wing is only 11mm thick and servo is supposed to be on the bottom of the wing. The wing and elevator are mounted flush with the bottom of the fuselage.This means control horns will become landing gear on our asphalt or grass runway. UGH. Mounted my servos in/on top of the wing. I cut square hole in exhaust for elevator control horn. Installed hook for bungee launch. Guessing CG is 80mm from wing LE. My bad for buying this thing.

• Overall
• Quality
• Value

Customer Rated

May 09, 2013

Hi, i recived my Silvia kit today. Looks nice, here are the component weights

Fuselage 344g
Left wing 64g
Right wing 62g
Elevator 22g
Canopy frame 6g
Canopy 8g
Hardware 40g

There was a EDF unit with my kit, PRODUCT ID: 701F, i also bought on. Now i got 2 EDF units. One for testing and one for blowing up ;)

It's going to be a challenge to accommodate batteries, 2X3cell might be ok. A 5cell pack is not going to be easy... there is room i the fuselage, but getting it in and out is a challenge! The canopy opening is narrow.

I am going with this motor PRODUCT ID: XK2858-3600KV and 5 or 6cell lipo on the 3 blade EDF.

Now on to the build....

Best regards
Simon
Norway

• Overall
• Quality
• Value

Customer Rated

Feb 07, 2013

Model comes with no instructions so I had to use the instructions from HET sniper Jet to just build it. Using foam I had to make a new airfoil shape on top of the main wing because the main wing doesn't have any type of airfoil shape to get this plane off the ground. The motor and fan assembly mount right underneath the main wing by doing this you will not be able to get the model within CG or carry any type of battery power.
This model is only for advanced builders. I would not recommend this for any beginner flyer intermediate flyer.

• Overall
• Quality
• Value

Customer Rated

Sep 28, 2012

arrived well packaged went together ok there are pre drilled holes for the elevator and wing just covered so dont make new holes the tail cone is very tiny but still manages to work the elevator servo mount fell to bits i just glued the servo to the inside the control horns are weak so buy some when u buy the jet everything else is great flies beautiful i used a hobby king / change sun 70mm 4 blade EDF hobby king turnigy 2836 3200kv motor zippy compact 1500mah 4S u can run a max battery of around 220grams without CofG problems CofG is 80-90mm back u will need to make your own exhaust ducting and EDF mounts i just used balsa u will also need to cut the inlet ducting to squeeze in the EDF as there is just no room and u will need a bungee cord to launch this model also there is no bungee hook included i used a small 3mm bolt and bent it to the shape of a hook overall great model flies beautiful check my video in the video section in the international silvia item

• Overall
• Quality
• Value

Customer Rated

Sep 26, 2012

arrived well packaged went together ok there are pre drilled holes for the elevator and wing just covered so dont make new holes the tail cone is very tiny but still manages to work the elevator servo mount fell to bits i just glued the servo to the inside the control horns are weak so buy some when u buy the jet everything else is great flies beautiful i used a hobby king / change sun 70mm 4 blade EDF hobby king turnigy 2836 3200kv motor zippy compact 1500mah 4S u can run a max battery of around 220grams without CofG problems CofG is 80-90mm back u will need to make your own exhaust ducting and EDF mounts i just used balsa u will also need to cut the inlet ducting to squeeze in the EDF as there is just no room and u will need a bungee cord to launch this model also there is no bungee hook included i used a small 3mm bolt and bent it to the shape of a hook overall great model flies beautiful check my video in the video section

• Overall
• Quality
• Value

Customer Rated

Aug 27, 2012

Personalmente no me dio resultado gaste mucho dinero en ponerle lo mejor como turbinas , motor y variador HET de la mejor calidad y como resultado logre on modelo super pesado con muchismos vicios a la hora de volar hasta que en el segundo vuelos el fuselaje se partio al medio cayendo y rompiendose en pedazos !

• Overall
• Quality
• Value

Customer Rated

Apr 13, 2012

A super jet! The design is simple but the flight is great. Very fast with the recommended engine, very maneuverable. You still need prvoir protection for the underside of the fuselage.

• Overall
• Quality
• Value

Customer Rated

Mar 17, 2012

THRUST TUBE IS A MUST.... I still haven't flown my Silvia yet do to endless weekends of rain rain rain. But my 4 s lipo has arrived and my UBEC so its ready to go. Static test showed me PATHETIC weak thrust. So i made a thrust tube from thin card board and folded it over and with some difficulty installed it successfully. Re tested static thrust and its a MASSIVE difference. If you do not make and install a thrust tube you will be missing out on A LOT of performance.

• Overall
• Quality
• Value

Customer Rated

Feb 28, 2012

This is nearly an exact copy of the HET Super Sniper 70.

Start with a CG of about 85mm aft 0f leading edge of wing at root.

• Overall
• Quality
• Value

Customer Rated

Feb 21, 2012

To see the BEST and safest way to get this plane in the air go to you tube and search this tittle ... Take off carriage alternative to hand launch or bungee launch.