TURNIGY AerodriveXp SK SeriesAerodriveXP SK Series motors are designed for those who want the very best in outrunner technology for their R/C plane. Typically an efficiency improvement of around 8-10% can be seen over similar classed motors. This is in part due to the following;Stator Laminations: .2mm
Magnet Type: N45SH
Bearings: Dual oversize (Japanese)
Idle Current: 1.3A
Rated Power: 1820w
Cell count: 4~8 Lipoly
Suggested Prop: 16x8, 16x10, 17x9
Power equivalent : .91+ glow engine
Unit Weight (g)
Max Currents (A):
Length B (mm):
Can Length D(mm)
Total Length E(mm):
I've put it into a 1,8 M Spitfire and I tested it with different props.
Turnigy battery 6 cell 5000 mAh 25-35 C, Turnigy ESC 120 A.
My personal experience (in full trottle):
15x8 plastic prop, 38A, 933W
18x8 plastic prop, 55A, 1327W
20x12 plastic prop, 87.5A, 2016W
21x12 wooden prop, 101A, 2288W
I had 20 starts with it, and it works excellently.
I think it is a valuable motor. It is worth buying.ho montato questo motore sul mio katana 120 sebart con regolatore sentilon100 elica 19/8 apc mi assorbe 65 amp , ci sto volando da diversi mesi ed sono veramente contento , ringrazio hk.ho montato questo motore sul mio katana 120 sebart, e regolatore sentilon 100, va benissimo, e ci volo da diversi mesi. molto importante regolare le impostazioni sul regolatore altrimenti si brucia sono veramente contento ringrazio hk.I have this motor now for more than 50 flights on a Sebart Angel 50. I have a Turnigy 6s 3600maH 30C plus Turnigy 85A ESC. I started with 16 X 10, where you have about 60 A. With this setup i goes very nice. But after i have read of a configuration with 18 x 10 i have tried this and i must say....very very nice. It is then 65 A, but you dont need to have full throttle at any time. So my recomendation is 18X10! (if you have enought place to the ground!!)
But since now i had no problems with loose magnets,etc.
Panzi June,2011I have 2 of SK5065/380.
very good for 26cc gas 3D plane conversion.
My Choice is 6S-5000mAh TGS 18x8-10 APC 18x8
ESC is HobbykingSS 90/100A only $30.
With TGS 18x10 6800rpm/75A 1.6kw.
It equals MLD28 or more.
Its not extreme performance but suit.
H9 ShowTime90 TGS 18x8 4.3kg
GW YAK54/26cc TGS 18x10 4.6KG
5065-380 HobbyKingSS-90/100A Turnigy 6S-5000
GoldWing YAK54 APC18x8/TGS18x10 4.6kg With Batt 6800rpm 75A
Hanger9 ShowTime90 TGS 18x8 4.2kg With Batt 7000rpm 73A
Makes about 6.5kg thrust.
This combination is berry cheap and usefull.
6S-ESC costs only $30.
Req Only One Charger.
Cheap 20C Lipos enough for.
My Specs re
SK5065 - 380 Turnigy 6S 5000mAh20C
Props TGS 18x10 18x8 APC 18x8E
GoldWing Yak54-26cc 4.6kg
APC 18x8E or TGS 18x10 6750RPM 75A
Hanger9 ShowTime90 4.3kg
TGS 18x8 6900rpm
very strong motor. Pulls 5 KG on 6S for competition F3A. Recommened.Second time that i buy engine. i use it for a MX2 186Cm from goldWing with a weight of 4,7Kg.
Using 6s 4000Mah Nanotech and a wood propeller 20*8. Using this plane with this configuration for 3D.the Motor pulls a lot of power and the magnets are strong glued, but the quality of the shaftholder is poor. i must fix it with 4 screws instead of the recomeded 2.