Country
United States
 
Shipped From:

Turnigy 480S BL Inrunner Motor w/ Impeller 3200kv

Turnigy 480S BL Inrunner Motor w...

Dimension: 47mm x 30mm, 60mm(with shaft)
Weight: 109g  (kv3200) (not including connectors)
Diameter of shaft:4mm
Length of front shaft:13mm
Lamination thickness: .2mm

Spec.
Battery: 3 Cell 3S/11.1...
D480S-3200

Now save save $0.00 $0

$26.55
OUT OF STOCK
149g
D480S-3200

Suggestion Box

Please let us know if you found any issues with this product listing.
We take our customer comments very seriously and in many cases our website modifications and product updates are a result of your comments!

Price War

If you've seen a product elsewhere for a better price, please let us know! HobbyKing pride themselves on offering the best price, so if there if you see something cheaper elsewhere, let us know!

Overview
Dimension: 47mm x 30mm, 60mm(with shaft)
Weight: 109g  (kv3200) (not including connectors)
Diameter of shaft:4mm
Length of front shaft:13mm
Lamination thickness: .2mm

Spec.
Battery: 3 Cell 3S/11.1V
RPM: 3200kv
Max current: 60A
No load current: 2.8A
Internal resistance: 22.3ohm
 
Data:
3S 11.1V
Prop: 4.75x4.75, 5.5x4.5
Max Current: 38.5A, 50A
Pull: 700g, 900g 
ESC: 60A
Battery Type: 3S Only
Specs

Additional Information

  • Blade Count:
    N/A
  • Speed (Sec/60deg):
    No
  • Torque(kg)(min. 0.01kg)
    No
  • Diameter X(Inch)
    No
  • A(mm):
    No
  • B(mm):
    No
  • C(mm)
    No
  • D(mm)
    No
  • E(mm):
    No
  • F(mm):
    No
  • SKU
    D480S-3200
  • Weight(g)
    149.00
  • Length:
    88.00
  • Width:
    45.00
  • Height
    50.00
  • Kv(rpm/v)
    3200.00
  • Max Currents (A):
    60.00
  • Power (W):
    0.00
  • Length B (mm)
    47.00
  • Can Length D(mm)
    45.00
  • Max Voltage(V):
    11.00
  • Shaft A(mm):
    4.00
  • Unit Weight (g)
    109
  • Diameter C(mm)
    30.00
  • Total Length E(mm):
    60.00
  • Resistance (mh):
    22.00
Discussion
Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Have mine in a "oldtimer" Multiplex Pico-Jet, and woow, a insane screamer on 3S .I believe it`s in the speed range of the Parkzone Stryker, maybe a little faster. ;) Do see other say its ok running it on 4S, I`l wont be doing that just yet. Even it`s tempting. The motor stays cool and it have lots of power. Quality seem`s really good too.
This is without a doubt the best motor I have ever owned. I put it in my FPV easyStar fully loaded, and this thing easily puts it into full vertical.

On a three cell it peaks at over 660 watts, and there is talk that it runs fine on a 4 cell.

Without a doubt, this motor has the best power/weight ratio I've ever seen.

and for $25? Wish I could rate it 10 crowns.
Put this on my old Zagi with a 6.5 x 5 prop HK 60amp ESC and Turnigy 2200mAh 3S 30C. Vertical climbs are possible, limited only by ones ability to see the model. ESC and motor get warm not hot. A great new lease of life to an old favorite model for around $60.
i think that is the best inruner motor.
I am using this motor on a Funjet with this
"Hobbyking SS Series 60-70A" ESC
Works great so far with a 6x5E prop
Which timing and other settings would you recommend?
Bought 2 of these for my funjet, 1 as a spare... draws about 70 plus amp and clocked a speed of 183 kph on a 4 cell setup... using a 4.5 X 4.5 prop.. sweet little thing!!! =) 2 Thumbs up for this motor... =)
Great motor! We use this on funjets and skyfun! On 4s with 5x5 prop!

It pulls around 100 amps and gives out around 1300 watts!

We tested it with a gps meter and my skyfun goes 235 kp/h!

Its a little beast!
moteur puissant avec belle finitions



merci hk

I use this in my funjet on 4s with 6x4 prop, pulling 76 amp and 960 watts, more than 50 flights with no problem, radar gun reads 132MPH, fastest motor on 4s setup I have ever had
These are well built motors with heaps of power, I used one for my high wing pusher/trainer.
View all reviews
Video
Upload video
File

Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.