New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Turnigy HV-380 Digital HV-3S Servo 10.40kg/ .030sec / 79g

Turnigy HV-380 Digital HV-3S Servo 10.40kg/ .030sec / 79g

Shipped From:
  • Global
Discontinued Product

Please continue searching for a similar product.
SKU:
HV380
WANT FREE SHIPPING? Click here to find out more!

Turnigy Alloy case, Titanium gear, High-voltage servo with dual large bearings.
Servos dont get better than this!
The Turnigy HV-Servos are the best bang-for-buck in the high performance servo category. Guaranteed!
Why waste money on over-marketed servos!? Trust Turnigy to deliver more than the required performance for your heli or plane.

Super eCCPM / High speed Cyclic servo use only.

Specification:
Dead band: 0.0008 ms (Default) 
Control System: +Pulse Width Control
Working frequence: 1520μs / 333hz 
(RX) Required Pulse: 3.5 ~7.4 Volt Peak to Peak Square Wave
Operating Voltage: 8.4 ~12.0 V DC Volts
Operating Temperature Range: -10 to + 60 Degree C
Operating Speed (8.4V): 0.040 sec/60° degrees at no load
Operating Speed (12V): 0.030 sec/60° degrees at no load
Stall Torque (8.4V): 7.30 kg.cm      (101.4 oz/in)
Stall Torque (12V): 10.40 kg.cm    (144.4 oz/in)
360° Modifiable:  NO
Motor Type:  Coreless Motor
Potentiometer Drive: Indirect Drive
Driver Type: FET
Bearing Type: Dual Ball Bearings
Gear Type: Titanium Gears
Programmable: NO
Connector Wire Length: 15.0 cm          (5.90 in)
Dimensions: 40X20X45 mm (1.57x0.97x1.77 in)
Weight:  79.1g              (2.79 oz)

  • SKU HV380
  • Brand Turnigy
  • Shipping Weight 169.0000
  • Packaging Length 0.00
  • Packaging Width 0.00
  • Packaging Height 0.00
  • Torque(kg)(min. 0.01kg) 10.40
  • Speed (Sec/60deg) 0.03
  • A(mm) 50.00
  • B(mm) 40.00
  • C(mm) 46.00
  • D(mm) 21.00
  • E(mm) 55.00
  • F(mm) 34.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

These servo drives are designed to operate from 3 cell Li-Po battery. I use these servos on my 700E T-Rex helicopter! For food, I installed the battery is Li-Po 3S 1500mah 20c. For interchanges, I used the bus power supply Power Bus (Skookum Robotics) Food tail servo Align DS650, gyro and receiver I have is BEC lowers the voltage to 6 volts. All very well, but the servo bit heated when I set up a home helicopter actuators heated up very much, I had to give them a cool cutting off the power.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

These servo drives are designed to operate from 3 cell Li-Po battery. I use these servos on my 700E T-Rex helicopter! For food, I installed the battery is Li-Po 3S 1500mah 20c. For interchanges, I used the bus power supply Power Bus (Skookum Robotics) Food tail servo Align DS650, gyro and receiver I have is BEC lowers the voltage to 6 volts. All very well, but the servo bit heated when I set up a home helicopter actuators heated up very much, I had to give them a cool cutting off the power.

one of my 3 cyclic servos was broke in flight causing the crash my elyq vision 50 competition. after that i disassemble servo and saw that DC motor is not working due to bended and melted brush. now i don`t know what should i do - sipmply change single broken servo and to hope that it was random and totally seldom event or change all cyclic servos to other tested and approved brand

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

one of my 3 cyclic servos was broke in flight causing the crash my elyq vision 50 competition. after that i disassemble servo and saw that DC motor is not working due to bended and melted brush. now i don`t know what should i do - sipmply change single broken servo and to hope that it was random and totally seldom event or change all cyclic servos to other tested and approved brand

I have not installed this servo in my .30 Nitro but I will soon. I hope the tail holds as well as everyone says it will with this and a JR G770 gyro.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I have not installed this servo in my .30 Nitro but I will soon. I hope the tail holds as well as everyone says it will with this and a JR G770 gyro.

trs bon servo , le top pour mettre au gaz

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

trs bon servo , le top pour mettre au gaz

I'm using on Align 750 gyro in my Aeuolus 600 and hold PERFECT. I'm doing inverted Huracane without any issues and backward flying, etc.

Is amaizing servo and now I'm testing them in my 27 Sback rudder (push-pull) system. Hablo hispano, porsi tienen alguna pregunta.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I'm using on Align 750 gyro in my Aeuolus 600 and hold PERFECT. I'm doing inverted Huracane without any issues and backward flying, etc.

Is amaizing servo and now I'm testing them in my 27 Sback rudder (push-pull) system. Hablo hispano, porsi tienen alguna pregunta.

los utilzare en mi t-rex 600 he decidido cambiar de marca ya que align me fallo en 2 ocaciones con servos que dejaron de funcionar, espero tengan un buen desempeo mejor que los align

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

los utilzare en mi t-rex 600 he decidido cambiar de marca ya que align me fallo en 2 ocaciones con servos que dejaron de funcionar, espero tengan un buen desempeo mejor que los align

hv380 is a perfect servo, my rudder is solid rock fast and perfectly center zero subtrim

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

hv380 is a perfect servo, my rudder is solid rock fast and perfectly center zero subtrim

Good comment. However the minus does not matter, but there is no + connection allowed between receiver and servo

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good comment. However the minus does not matter, but there is no + connection allowed between receiver and servo

Great Servo, powerfull and fast. I use it on my HK600 GT. My solution is to use 3s LiPo wit an 5A ubec. I connect the + from ubec to the receiver and gyro and connect only the signal wir from servos to receiver. The + - wire from LiPo is connected directly to the servo.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Great Servo, powerfull and fast. I use it on my HK600 GT. My solution is to use 3s LiPo wit an 5A ubec. I connect the + from ubec to the receiver and gyro and connect only the signal wir from servos to receiver. The + - wire from LiPo is connected directly to the servo.

Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save