MultiStar ESCs are are a quality speed controller at a fantastic price! Designed for simple installation and easy setup these ESCs have proven to offer excellent performance when used in Multi-rotor applications. If your starting out in Multi-rotors and need an easy to install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered.
These ESC's features a very smooth yet linear throttle response, without sacrificing a rapid, crisp, response to any throttle input. Safety is not forgotten with all Multistar Esc's featuring adjustable battery LVC (set battery type to LiXX to disable LVC), stalled motor (overload) protection, signal loss shut-down and safe arming.
All Multistar series ESC's come with bullet connectors installed that are suited to the ESC's rated power handling. This allows for plug and play convenience by simply adding the appropriate battery supply splitter (3,4 or 6 ESC) and motor lead extensions from the Multistar modular accessory line. What could be simpler?
All Multistar ESC's feature an ATmega MCU that opens the door to customizable firmware - for those so inclined! or alternatively a programming card can be used with the installed software for quick and easy setup with the pre-flashed software.
Please refer to the related items below for a solder free multi-rotor power solution to suit your next multi-rotor project.
• Smooth and linear throttle control
• Fast response to throttle input
• Atmel MCU
• Stalled motor protection
• Throttle signal lose protection
• Safe power-on (throttle lockout)
• Support 480Hz+ high refresh rates (up to 499hz)
• Compatible with programming card
Constant Current: 10A
Input Voltage: 2-3 cell Lipoly
BEC: Yes (linear) [Remove middle wire to dissable]
BEC Output: 5V/2A
PWM: 8 KHz
Max RPM: 240,000rpm for 2 Pole Brushless Motor
PCB Size: 22mm x 17mm
Discharge Plugs: Male 2mm Bullet Connector
Motor Plugs: Female 2mm Bullet Connector
User manual now available for download under "Files" tab.
So tiny and lightweight and perfect! Already ready to go with 2mm connectors on all the wires. At this price its a no brainer.. Perfect for my 250!Don't bother with these they don't perform well at all. and can not be flashed with socket tool as atmega chip is to small very small. wast of money get some Simon k instead I'm very disappointed with these want my money back their useless for multi rotors!!!!!!Mis avec turnigy multistar 1704 pas de surchauffe bon varioBought these for my 250 mini quad with multistar 1704 motors and mini APM flight controller. I did also got the program card and set them up best i can. Even on NIxx on lowest setting my battery alarm goes off and they are already cutting the power to the motors. I am gonna try the HK f10a flashed with simonk next as these will eventually lead to a bad crash. Also the overload cut off is annoying because if you touch back down one or more motors will quit and you have to disarm and rearm. I am not sure why they engineered these the way they did since basically they are not good for multirotors at all??Good esc(s) placed in my 330 frame with a KK2.1 board flashed with 1.11 firmware, 3s 1000mah Zippy compact batt, Turnigy 10amp Multistar esc(s) 8ch 9x receiver, power board soldered the esc direct to it and XT60 batt plug on it, 8045 props, this thing it a rocket and getting 6 minutes flight time. After flight everything is cool. Will hoover with only 40pcnt throttle. Motors are Turnigy D2822/17 1100 kv. I did soldered 3.5 bullet ends on everything.No better than any non flashed esc for multirotors, after flashing with simonk they are 10x better, but this is not easy as there are no pads and the hk flashing tool is too big for the atmega chip on this esc, so you have to solder directly to the chips pin outs. For this reason I would not buy anymore as there are others available that are far easier to flash. If they are specifically for multirotors why does it have brake settings, set to medium as default lol.
They also have no throttle calibration, they are auto like dji escs, but you get throttle calibration when flashed.i've got a few brands of 10amps this is the one which fits me the best especially compared to the piece of crap red brick also from here...Really cool ESC for mini quadcopter. I use them with Turnigy Multistar 1704-1900K, kk2.1. And works well. I calibrated them straight kk board.nice little ESC. Runs without flashing to SimonK also good enough for smaller Multicopter.Works ok, but gets hot faster than eg. the tgy plush esc. Bought a bunch for a small quad and put another on a bonsai flying wing. Dont forget to get the programming card too!
Manual - Turnigy Multistar Brushless ESC download now [2384kb] Multistar 10A SimonK 1 download now [115kb] No File Name download now [94kb] Turnigy Multistar ESC Manual download now [2384kb] No File Name download now [214kb] Multistar 10A flashed with simonk 1 download now [819kb] Multistar 10A flashed with simonk 3 download now [3348kb] Multistar10A-1 download now [229kb] Multistar10A-2 download now [167kb] Turnigy ESC All download now [2298kb]