New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Turnigy Multistar USB BLHeli Programmer For V2 Multistar ESC

Turnigy Multistar USB BLHeli Programmer For V2 Multistar ESC

Shipped From:
  • Global
QTY:

Now save save $0.00 $0.00

$7.55
Status:
In Stock
Weight:
15 g
SKU:
9351000056-0
WANT FREE SHIPPING? Click here to find out more!

The Multistar USB tool for all V2 Multistar ESC’s. Multistar ESC's feature an ATmega MCU that opens the door to customizable firmware – The V2 Multistar comes with BLheli software pre-installed, and for those so inclined this easy to use USB tool is available for Configuration and updating via the BLHeli Suite GUI. This allows you to easily reverse motor direction without changing motor wires, adjust a host of setting to include Demag compensation and timing for Hi-KV motors with Sync issues.

 

MultiStar ESCs are a quality speed controller at a fantastic price! Designed for simple installation and easy setup these ESCs have proven to offer excellent performance when used in Multi-rotor applications. If you're starting out in Multi-rotors and need an easy to install solution that is tested and proven to work with Multi-rotor craft then these speed controllers have you covered.

 

To use the programming tool simply download the free BLHeli suite software plug the USB tool into the computer and select the comport, next connect the receiver connection wire from the ESC to the USB tool and turn power onto the ESC. Press connect and adjust parameters as needed and select flash and you’re done.

 

Note: The tool is for the Multistar V2 series of ESC and use with BLHeli suite GUI software, And is not compatible with other ESC’s.

  • SKU 9351000056-0
  • Brand Turnigy
  • Capacity (mAh) -
  • Shipping Weight(g) 15.00
  • Length 60.00
  • Width 10.00
  • Height 10.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Ironically, I came here to give it a bad review due to lack of instructions, and then I found the instructions I needed in the reviews. It works as intended, but minus one point for the lack of instructions.

trending_up Value:
verified_user Quality:
playlist_add_check Overall:

Ironically, I came here to give it a bad review due to lack of instructions, and then I found the instructions I needed in the reviews. It works as intended, but minus one point for the lack of instructions.

turnigy buenos productos y bajo costos

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

turnigy buenos productos y bajo costos

Fantastic item, I use it all the time in all places and electronics. Nice n shiny finish, good covering finish.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Fantastic item, I use it all the time in all places and electronics. Nice n shiny finish, good covering finish.

LHeli with 15A Multistar ESC with Multistar USB Tool

- BLHeli: https://blhelisuite.wordpress.com/

- Multistar USB Tool with out reed wiere!

- De Multistar ESC feed with 5Volt from ext.BEC!

-
Settings BLHeli

1. install the driver

2. start BLHeli Suite

3. Select Amtel/Silabs Interface = 1 Amtel BLHeli Bootlader (USB/Com)

4. Plug in USB programmer into your computer

5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]

6. Select the correct speed (Baud 9600)

7. Connect ESC plug into USB programmer (without the red cable !!!)

8. Click on Connect

9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)
-
Eanable One Shot in BL Heli


- PWM Frequency/Damping = Light

- Motor Timing = High

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

LHeli with 15A Multistar ESC with Multistar USB Tool

- BLHeli: https://blhelisuite.wordpress.com/

- Multistar USB Tool with out reed wiere!

- De Multistar ESC feed with 5Volt from ext.BEC!

-
Settings BLHeli

1. install the driver

2. start BLHeli Suite

3. Select Amtel/Silabs Interface = 1 Amtel BLHeli Bootlader (USB/Com)

4. Plug in USB programmer into your computer

5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]

6. Select the correct speed (Baud 9600)

7. Connect ESC plug into USB programmer (without the red cable !!!)

8. Click on Connect

9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)
-
Eanable One Shot in BL Heli


- PWM Frequency/Damping = Light

- Motor Timing = High

Einwandfreie Funktion mit den 6A V2 Reglern.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Einwandfreie Funktion mit den 6A V2 Reglern.

Works fine.
I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire of the USB programmer and to power the ESC from a BEC 5V.

Procedure (to combine with LeBobo's MultistarV2 Pack ) :
1. install the driver
2. start BLHeli Suite
3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
4. Plug in USB programmer into your computer
5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
6. Select the correct speed (Baud 9600)
7. Connect ESC plug into USB programmer (without the red cable !!!)
8. Click on Connect
9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works fine.
I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire of the USB programmer and to power the ESC from a BEC 5V.

Procedure (to combine with LeBobo's MultistarV2 Pack ) :
1. install the driver
2. start BLHeli Suite
3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
4. Plug in USB programmer into your computer
5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
6. Select the correct speed (Baud 9600)
7. Connect ESC plug into USB programmer (without the red cable !!!)
8. Click on Connect
9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

Works fine.
I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire and power the ESC from a BEC.

Procedure (to combine with LeBobo's MultistarV2 Pack ) :
1. install the driver
2. start BLHeli Suite
3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
4. Plug in USB programmer into your computer
5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
6. Select the correct speed (Baud 9600)
7. Connect ESC plug into USB programmer (without the red cable !!!)
8. Click on Connect
9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Works fine.
I read config from my Multistar 10A V2; it was in version 11.7. I flashed with new version 13 of BLHeli and I adjusted some settings. The only trik is to cut the red wire and power the ESC from a BEC.

Procedure (to combine with LeBobo's MultistarV2 Pack ) :
1. install the driver
2. start BLHeli Suite
3. Set "ATMEL / SILABS" to "ATMEL 1-Wire Bootloader Interface"
4. Plug in USB programmer into your computer
5. Select the correct port: COM xx [USB SERIAL CH340 (COM xx)]
6. Select the correct speed (Baud 9600)
7. Connect ESC plug into USB programmer (without the red cable !!!)
8. Click on Connect
9. Click on ReadSetup and quickly connect Lipo at ESC (you have 2 or 3 seconds)

I use this USB programmer with Multistar 10A and I haven't got any problem.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I use this USB programmer with Multistar 10A and I haven't got any problem.

It is not a programmer for Multistar, it is a universal programmer from Multistar.
The stick has always worked with BLHeliSuite, with ANY Atmel based ESC, which has the small 512 bytes BLHeli bootloader flashed over ISP (and which do not have an inverted input, like the Multistar V1 ESC have). It has NOT been specially build for Multistar ESC nor is it somehow bound to work only with Multistar ESC.
All the negative reviews address the Multistar V2 ESC, not the this Multistar programmer.
As far, as it tested, it works great and is easy to use.
The best solderless ready-built adapter for the small 512 bytes BLHeli bootloader (or other 1-Wire AVRootloader solution).

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

It is not a programmer for Multistar, it is a universal programmer from Multistar.
The stick has always worked with BLHeliSuite, with ANY Atmel based ESC, which has the small 512 bytes BLHeli bootloader flashed over ISP (and which do not have an inverted input, like the Multistar V1 ESC have). It has NOT been specially build for Multistar ESC nor is it somehow bound to work only with Multistar ESC.
All the negative reviews address the Multistar V2 ESC, not the this Multistar programmer.
As far, as it tested, it works great and is easy to use.
The best solderless ready-built adapter for the small 512 bytes BLHeli bootloader (or other 1-Wire AVRootloader solution).

Customer files
Connecting_ESC.png Download [601]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save