Precio total

0,00 €

Carrito de compras 0 Carrito de compras 0 Loading...

Turnigy EasyMatch Serie G46 - Eje de reemplazo

Generating Links

Turnigy EasyMatch Serie G46 - Eje de reemplazo

Precio:

Now save ahorra 0,00 € 0,00 €

2,56 €
Cantidad:
Enviado desde:
  • Global
Ya comprado
Tiempo estimado de llegada: Sin Hora Estimada De Llegada [ ? ]
Estado:
Pedido pendiente
SKU:
031000018
¿Envío gratis? ¡Haga clic aquí! aprender más!

Turnigy EasyMatch Serie G46 - Eje de reemplazo

Especulación.
Longitud del eje: 76mm
Diámetro del eje: 6 mm

attributeset-10
Close

Dimension Diagram Guide

  • attributeset-10

Close

Subir video

Regístrese para subir videos, por favor Iniciar Sesión o registrarse

Temas
Ordenar por
Temas más recientes
* Apodo:

* Tu respuesta:


Ingrese el texto que se muestra en la imagen en el campo de abajo
*Código de verificación:
Cancelar
Enviar
Publica un tema nuevo
* Apodo:

* Tu tema:



Ingrese el texto que se muestra en la imagen en el campo de abajo
*Código de verificación:
Publicar tema

Regístrese para escribir reseñas, por favor Iniciar Sesión o registrarse

Kiwibob | Comprador verificado

  • Quality
  • Overall
  • Value

Replacement shaft

Jan 28, 2022

Purchased G46 shaft and fitted it t=o the motor without any problems

David B | Comprador verificado

  • Quality
  • Overall
  • Value

G46 back to life

Nov 20, 2021

Thank you HobbyKing for making this replacement shaft available, it has enabled me to repair a perfectly good motor and bring it back to life. Here’s an account of how I did it.
I needed to replace a crash-bent shaft in my G46 550kV motor. The grub screws came out without too much trouble but pulling apart the stator and rotor bell was a tough job because of the strong magnets. Once I had managed to pull them apart, I could not press (in my vice) the shaft out of the rotor bell. Possibly some thread locker had wicked its way from the grub screw along the shaft or perhaps it was a tight interference fit. Anyway, a friend recommended heating the rotor bell with a hot air gun on the principle that since it was made of an aluminium alloy it would expand more that the steel shaft and would therefore allow the shaft to be pressed out. Using strips of thin card wrapped around the body of the rotor bell, I created a protective jacket that was just under 4mm thick. The purpose of this was to minimise heating of the rotor bell’s body - I didn’t want to risk de-magnetising the magnets or weaken the bond of the glue holding the magnets in place. I put a few drops of water onto the top of the jacket to prevent it burning when heat was applied to the nose of the rotor bell. I used a hot air paint stripper gun to apply the heat and was then able to press the shaft out (in my vice), very easily. It looked like some thread locker had indeed wicked in between the shaft and rotor bell, so I carefully removed this with a small file.
The motor had three bearings, two off size 6x12x4 (MR126 ZZ) in the nose of the rotor and one off 6x19x6 (626 ZZ) in the stator. Since one of the nose bearing was damaged, I decided to replace all three, which I purchased from SMB Bearings Ltd, in Carterton, UK.
Using my digital caliper I compared the replacement shaft diameter with the original. Both were exactly the same. The replacement shaft was a tight fit, but it could be fitted by hand - no vice required. The motor is now working just as good as new.

Eric | Comprador verificado

  • Quality
  • Overall
  • Value

Very slow delivery!

Dec 06, 2020

Very slow delivery

Rusty | Comprador verificado

  • Value
  • Quality
  • Overall

Shaft

Nov 19, 2019

Good spare

Gary | Comprador verificado

  • Overall
  • Value
  • Quality

Nice

Oct 03, 2019

Exactly as ordered

Subir archivo

Regístrese para subir archivos.
Por favor registrarse o registrarse para empezar a ayudar a los aficionados ahora!