Multistar V-Spec 1304-3100KV Multi-rotor do motor (CW)

• Overall
• Quality
• Value

Good and low priced

Aug 14, 2018

i have a couple of these on small wings and i run them hard and get them hot almost every day. Only one failed and that was from running it on 3s hard 'cause I wanted to see if it would last. It lasted about 3 min running hard on a Scythe wing with a 5030 prop, then poof. Don't run it on 3s. Well, don't run it very hard on 3s that is.

• Overall
• Quality
• Value

Good quality, works nicely, good for small scratch build designs

May 24, 2018

Using it on a converted toy foam glider with an 700 mm wingspan. Works nicely. You can find 5 inch props with 4 mm hub on Hobbyking.

• Overall
• Quality
• Value

freat little motor

May 14, 2018

I used on 130mm frame with 3s 800mah and 3041 props 4 blade, run smooth and not even warm.
Didnt like that is not included any bolts, overall great deal.

• Overall
• Quality
• Value

Nice and tiny

Feb 16, 2018

The Motors look very nice and the quality seems to be good. But i´m missing some screws in the box and i think that is a must have!

• Overall
• Quality
• Value

Mising the motor bolts

Dec 28, 2017

I can only give 3 stars across board for not including motor mounting bolts of any kind,
mounting bolts cost a fraction of a penny/cents to include, even if they are too short or too long; we don't have a problem seeking out bolts to suit our needs and store the ones supplied for another project! but to supply Nothing is begging a Negative so I have given 3 stars even before getting to mount the motor. R

• Overall
• Quality
• Value

Customer Rated

Aug 11, 2016

This little thing is Awesome! I used it to power a HobbyKing Ridge Ryder using a Turning plush 10A esc, and 0.8mah 2s.

• Overall
• Quality
• Value

Certified Buyer Rated

May 22, 2016

these motors are great the only reason i am giving them a 3 star is because of miss shipment and 2 broken motors out of 12

• Overall
• Quality
• Value

Customer Rated

Feb 25, 2016

I bought these for the size. Got them in and found there are no adapters for the 2mm shaft to the 5mm hubs for propeller. If you get these, plan on making your own adapters.

• Overall
• Quality
• Value

Customer Rated

Feb 21, 2016

I'm a little bit surprised that these motors are still so unknown and without any review here.
I'm following like so many the new trend of 1306 motors with only 3-3,5 inch props and full FPV stuff for AUW around 200g. I was looking for some lighter alternatives than 1306 but bigger/more powerful than 1104/1105 (which are great but not enough for 200g AUW).
And these 1304 fit perfectly in the gap between 110x and 1306 motors. Weight without nut (where I always use lighter and better stop nuts) is only 7,7g which ist around 4g less than usual 1306, so saves about 16g overall which is a lot for micro quads.
Thrust with 3-4 inch is similar as with 1306 but keep in mind that these 4g less means 1/3 less metal to cool down high currents! So 4S 4" may be to much or 5" 3S.
I personally would not use this motor for 5". They are great with the pricy Rotorx RX3040T or with Gemfam 3545BN GF/Nylon reinforced.
More kV would be nice as many people will use this motor only for 3-4 inch.
Sound/smoothness is fine so far, let's add some more test flights to give 5 Stars quality.
Motor cables are like most 1306 so-so and easy to break at the ESC soldering. So still room for improvement. The only small motors I know which do much better here with soft cables and multiple fine wires are RCX (even until 1105 size) and DYS 1306.