New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

2804-210Kv Brushless Gimbal Motor (Ideal for GoPro to Compact Style Cameras)

2804-210Kv Brushless Gimbal Motor (Ideal for GoPro to Compact Style Cameras)

Shipped From:
  • USA
  • Global
QTY:

Now save save $0.00 $0.00

$13.23
Status:
In Stock
Weight:
31 g
SKU:
047000029-0
WANT FREE SHIPPING? Click here to find out more!

Looking to make your video platform ultra-smooth? This is the ultimate in smooth high pole count purpose built brushless gimbal motors.

The 2804 motor comes with flush mounting so any DIY to PRO projects are simple and straight forward, it also comes with the standard female connector pre-installed, So wiring is as simple as plugging it in. It’s a perfect match to our Brushless Gimbal Stabilization Board and IMU.

The 2804 is the perfect size for cameras around 100-300 grams (GoPro style).

Spec:
Poles: 12N14P
KV(RPM/V): 210
Resistance: 10.4omh
Weight: 35g
Wire: 0.19mm
Torque: 240g
Bottom holes center to center: 16mm and 19mm
Top holes center to center: 12mm

  • SKU 047000029-0
  • Brand Other
  • Shipping Weight(g) 31.00
  • Length 35.00
  • Width 15.00
  • Height 35.00
  • Kv(rpm/v) 210.00
  • Unit Weight (g) 35
  • Max Current (A) 0.00
  • Resistance (mh) 10.00
  • Max Voltage(V) 0.00
  • Power (W) 0.00
  • Shaft A(mm) 0.00
  • Length B (mm) 15.00
  • Diameter C(mm) 34.00
  • Can Length D(mm) 10.00
  • Total Length E(mm) 15.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Good motor, I use it for roll in a 3 axis gimbal, I enlarged the threads to 3mm though. very simple to do, just disassemble the rotor and insert a 3 mm tap, work slowly, add a bit of oil. No predrilling required. Assemble it back. Bought two, one had a minute play if you pulled on the rotor casing, just put it on a board of soft wood rotor down and slightly tap it with a small hammer on the shaft (circlip end, do not remove the circlip) checking for play. Adjust the hammer power by slightly increasing it if there's still play. Don't over do it!

I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.

If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I used these for a decently heavy 3D printed gimbal of my own design. The camera housing weighed 325 grams and these motors worked fine, but was nearing the threshold of over-drawing the 500 mA max that the Tarot gimbal control gives. I tried to use these motors on a 425 gram camera and they would not stabilize the gimbal within the 500 mA allowance of the gimbal controller.

If you decide to design your own gimbal, these will work great on cameras in the 100-300 gram threshold. Remember that gimbal design is mostly about balance than it is about torque. Also, the more jostling your quadcopter or craft does, the more torque you have to put out. So, test your stuff on the ground liberally before flying it!

these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher quality

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

these motors should have high quality bearings with no clear ens to the axles images are shaky and a lot of wobble, my next motors will be of a higher quality

meka kama nahe podi e ne neda

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

meka kama nahe podi e ne neda

I bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

I bought 6 units of this motor and only 2 of them work. The windings are open on the rest. Hobbyking needs to improve quality checks ASAP ! I also bought 3 controller boards and 1 unit came with a DIODE bad. Had to replace it myself.

Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

Perfect motor for GoPro H3 (Roll-axis). Buy the smaller motor for pitch.
Smooth and silent. Very happy with mine.

enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci

verified_user Quality:
trending_up Value:
playlist_add_check Overall:

enfin ces moteurs chez HK , la on va pouvoir ralis ces propres nacelles a moindre cot comme d'habitude chez HK.
merci

Customer files
047000029-0 -43040.JPG Download [81]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Related Tags

Combine Essential Items and Save