New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Orange R8DM 8Ch DMSS Receiver

Orange R8DM 8Ch DMSS Receiver

Shipped From:
  • Global
QTY:

Now save save $0.00 $0.00

$18.46
Status:
In Stock
SKU:
9014000042-0
WANT FREE SHIPPING? Click here to find out more!

The Orange R8DM is a 2.4GHz DMSS compatible receiver that is designed for use with JR DMSS 2.4GHz transmitters, such as XG6,XG7,XG8 ,XG11 and XG14 under DMSS protocol mode.

Affordable and with a great reputation for reliability, Orange receivers are a fantastic alternative for budget conscious hobbyists and this 8 channel receiver for JR 2.4Ghz transmitters is just outstanding value. 

Features:
• Full Range Receiver
• 8 Channels - Throttle, Aileron, Rudder, Elevator, Gear, Aux1, Aux2, SBAux3. 
• SBUS support on channel 8 (Aux3)
• For use with JR DMSS transmitters
• Light weight
• Fail Safe Programable

Specs:
Model: RG831B 
Type: Full range receiver 
Channels: 
Modulation: DMSS 
Band: 2.4GHz 
Weight: 11g
Voltage Range: 3.6V~8.5V 

  • SKU 9014000042-0
  • Brand -
  • Capacity (mAh) -
  • Shipping Weight 24.0000
  • Packaging Length 145.00
  • Packaging Width 18.00
  • Packaging Height 100.00
  • How to Bind
  • How to get S-Bus output
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Binds instantly, solid radio link. Amazing value for an 8ch Rx. Pity no telemetry but lets hope HobbyKing bring out another version with telemetry soon. How about stocking in the UK or EU warehouse too?

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

Binds instantly, solid radio link. Amazing value for an 8ch Rx. Pity no telemetry but lets hope HobbyKing bring out another version with telemetry soon. How about stocking in the UK or EU warehouse too?

Binding was no issue for me and went smoothly. No range issues and works as it should. You can't beat the price/value! I'm definitely going to buy another 4 as I hate pulling radios out out of planes. I'm using a JR XG14 transmitter.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

Binding was no issue for me and went smoothly. No range issues and works as it should. You can't beat the price/value! I'm definitely going to buy another 4 as I hate pulling radios out out of planes. I'm using a JR XG14 transmitter.

How to Bind:
The instructions are dire, ignore them.
I had success (after many many attempts) this way:
Put the shorting plug on ch7 if using XG8/ 14/ 11
Turn TX on, don't use bind mode.
Ensure XBus is off (it is by default)
Power-up RX with binding button held down for 1-2 secs
If successful, LED near binding button goes green
Power down, remove binding plug, range check and go fly.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

How to Bind:
The instructions are dire, ignore them.
I had success (after many many attempts) this way:
Put the shorting plug on ch7 if using XG8/ 14/ 11
Turn TX on, don't use bind mode.
Ensure XBus is off (it is by default)
Power-up RX with binding button held down for 1-2 secs
If successful, LED near binding button goes green
Power down, remove binding plug, range check and go fly.

I bought 2 of R8DM. One was put to ASW28. When bind has to follow the instruction and use the tiny plastic screw drive to push switch on bottom side of Rx. My Tx is JR XG-14, so need to plug the short wire into channel AUX7 in order to bind. (No success if plug into AUX6).
To start bind my system:-
- Switch the Tx to "on" and in the function ready to initiate the bind. (don't start bind yet).
-At Rx, after insert the short wire to AUX7, while push the back side switch of Rx with plastic screw driver connect the battery to supply power to Rx.
-Immediately at the Tx press to bind (needs to many hands).
-The green light on, binding success.
Flight test- I have flown my ASW28 upwind to the height that hardly see it. I works as it should. So happy with this product. will buy more soon.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

I bought 2 of R8DM. One was put to ASW28. When bind has to follow the instruction and use the tiny plastic screw drive to push switch on bottom side of Rx. My Tx is JR XG-14, so need to plug the short wire into channel AUX7 in order to bind. (No success if plug into AUX6).
To start bind my system:-
- Switch the Tx to "on" and in the function ready to initiate the bind. (don't start bind yet).
-At Rx, after insert the short wire to AUX7, while push the back side switch of Rx with plastic screw driver connect the battery to supply power to Rx.
-Immediately at the Tx press to bind (needs to many hands).
-The green light on, binding success.
Flight test- I have flown my ASW28 upwind to the height that hardly see it. I works as it should. So happy with this product. will buy more soon.

Pas encore testé la portée.
Bind immediat avec XG8 sans même mettre le TX en mode binding. Il suffit de suivre la notice.
ATTENTION: chaque modèle a sa propre signature émetteur donc si vous changez de modèle, il faut refaire le bind du RX.
C'est parfait, je recommande.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

Pas encore testé la portée.
Bind immediat avec XG8 sans même mettre le TX en mode binding. Il suffit de suivre la notice.
ATTENTION: chaque modèle a sa propre signature émetteur donc si vous changez de modèle, il faut refaire le bind du RX.
C'est parfait, je recommande.

Pas encore testé la portée.
Bind immediat avec XG8 sans même mettre le TX en mode binding. Il suffit de suivre la notice.
ATTENTION: chaque modèle a sa propre signature émetteur donc si vous changez de modèle, il faut refaire le bind du RX.
C'est parfait, je recommande.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

Pas encore testé la portée.
Bind immediat avec XG8 sans même mettre le TX en mode binding. Il suffit de suivre la notice.
ATTENTION: chaque modèle a sa propre signature émetteur donc si vous changez de modèle, il faut refaire le bind du RX.
C'est parfait, je recommande.

Bought 4 as an initial test on an XG8, at first I had difficulty binding, then I realised it doesn't use the conventional JR binding procedure. Switch on your radio, Press the bind button on the Rx, and power Rx. Hold down while powered, light will go from Red to Green. Then it's bound to the radio. I compared range tests against an actaul JR Rx, the JR receiver started to loose bind about 20 paces before the OrangeRx.So on range this receiver outsmart JR receivers. As for quality, the plastic casting is held by 4 small plastic clips, so if you glue/double side tape it, it easily separates from the bottom part. I hot glue mine inside just to make it more sturdy and less vibration prone. Tested S-Bus on a MSH Brain flybarless unit, noticed that instead of decreasing travel like with JR xBus rx's I had to increase travel to almost over 140% on channels. Other than that it worked fine with S-Bus. Value for money this little DMSS receivers are well worth it.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

Bought 4 as an initial test on an XG8, at first I had difficulty binding, then I realised it doesn't use the conventional JR binding procedure. Switch on your radio, Press the bind button on the Rx, and power Rx. Hold down while powered, light will go from Red to Green. Then it's bound to the radio. I compared range tests against an actaul JR Rx, the JR receiver started to loose bind about 20 paces before the OrangeRx.So on range this receiver outsmart JR receivers. As for quality, the plastic casting is held by 4 small plastic clips, so if you glue/double side tape it, it easily separates from the bottom part. I hot glue mine inside just to make it more sturdy and less vibration prone. Tested S-Bus on a MSH Brain flybarless unit, noticed that instead of decreasing travel like with JR xBus rx's I had to increase travel to almost over 140% on channels. Other than that it worked fine with S-Bus. Value for money this little DMSS receivers are well worth it.

The receiver setup is different from original receiver and you should notice:
1. The negative pole of the wires (black) facing down - toward the button side.
2. Binding: open new model in your transmitter (in system mode), throttle stick down. better that there will be NO other open 2.4Ghz sources near the receiver during the binding (like portable telephones/ telephone base, WiFi routers etc.)
3. Put the shorten binding cable plug in the right place in the receiver (Ch 6 for R8DM and XG7). you can also connect one servo for checking the binding. Operate
the transmitter ON in REGULAR working mode with the NEW model selection. connect the battery to the receiver while pressing the button and then release the button. red light shown.
4. Wait! . NO need to operate the transmitter in binding mode - just REGULAR working mode.
5. After about 30 seconds the light is changing to green. thats it. it should work, you can also see the connected servo moving.
6. Disconnect everything. Good Luck!

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

The receiver setup is different from original receiver and you should notice:
1. The negative pole of the wires (black) facing down - toward the button side.
2. Binding: open new model in your transmitter (in system mode), throttle stick down. better that there will be NO other open 2.4Ghz sources near the receiver during the binding (like portable telephones/ telephone base, WiFi routers etc.)
3. Put the shorten binding cable plug in the right place in the receiver (Ch 6 for R8DM and XG7). you can also connect one servo for checking the binding. Operate
the transmitter ON in REGULAR working mode with the NEW model selection. connect the battery to the receiver while pressing the button and then release the button. red light shown.
4. Wait! . NO need to operate the transmitter in binding mode - just REGULAR working mode.
5. After about 30 seconds the light is changing to green. thats it. it should work, you can also see the connected servo moving.
6. Disconnect everything. Good Luck!

I have got mind to bind to the JR XG 14 7 the JR 28X.
Need to have the transmitter in the binding mode before powering up the receiver.
Good range as well.
Better binding would make a far better receiver.
Bob

verified_user Quality:
playlist_add_check Overall:
trending_up Value:

I have got mind to bind to the JR XG 14 7 the JR 28X.
Need to have the transmitter in the binding mode before powering up the receiver.
Good range as well.
Better binding would make a far better receiver.
Bob

I have JR XG-6 XG-8 and 28X transmitters.
I was not able to bind the receiver to any one of these transmitters.
I followed the instructions and tried dozens of times.
Either my particular unit was defective, or there is a design problem.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

I have JR XG-6 XG-8 and 28X transmitters.
I was not able to bind the receiver to any one of these transmitters.
I followed the instructions and tried dozens of times.
Either my particular unit was defective, or there is a design problem.

  1. 1
  2. 2
Customer files
Orange Rx R8DM R6DM R4DM DMSS Receiver M Download [369]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!