-
Product
Description -
Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.
The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.
The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.
Specs.
Turns: 20T
Voltage: 2~3S Lipoly
RPM/V: 1020kv
Internal resistance: 0.11 Ohm
Max Loading: 18A
Max Power: 168W
Shaft Dia: 3.0mm
Bolt holes: 16mm & 19mm
Bolt thread: M3
Weight: 58g
Motor Plug: 3.5mm Bullet Connector -
Product
Specifications -
Additional Information
-
SKU:
SK3-2830-1020
-
Brand:
No
-
Shipping Weight(g)
129.00
-
Length
110.00
-
Width:
45.00
-
Height:
80.00
-
Kv(rpm/v)
1020.00
-
Unit Weight (g)
58
-
Max Currents (A):
18.00
-
Resistance (mh):
110.00
-
Max Voltage(V)
11.00
-
Power (W)
168.00
-
Shaft A(mm):
3.00
-
Length B (mm):
32.00
-
Diameter C(mm)
28.00
-
Can Length D(mm)
16.00
-
Total Length E(mm):
44.00
-
SKU:
-
Community
Discussions -
-
Rate&
Review -
Winding insulation, very bad. I use 40Amp ESC , and after two crashes, I lost two motors, because of blocking propelers. Smell bad !These are an excellent smooth motor. I am using them on my quad in combination with simonk flashed Blueseries.rn gzel bir ambalajla aksesuarlar ile beraber geliyor. Multicopter iin almtm ve eer sk450 quadcopter frame alacaksanz, frame'i modifiye etmeniz gerekiyor. Aksi halde motor mili montaja izin vermiyor. Ben beenerek kullandm. Bir krmdan sonra motor millerinde hafif bir yamulma olduunu hissettim ve o haliyle ok ucuza sattm. Tabi satarken krmdan bahsettim.Ordered one for an electrifly nieuport 11, very satisfied by the engine. well engineered, complete accessories, and a nice packing (i know we don't fly the box, but that's a pleasure to open it). Connected to a plush 20 , a 1650 3s , and 10x5 APC style
Regarding my appliance, a bipe weighting about 700 g, the engine is overpowering, i take off half throttle, fly on a third or a fourth.
I see this motor really matching the specs, no doubt i will buy another one for my next dare sopwith tripe. Shall i say i recommend it ?I place that motor in my Pitts and now flyies very fast with prop 10x5. Very strong motor for the sizeseems like a good motor, just dont expect to use the bottom housing mounts, the screws are so thin a baby would strip them. also the wires come out of the housing in different holes in relation to the mounting plate between motors.I buy it to replace the extra 260 motor. amazing quality for the price.I always re-wind Turnigy motors when I buy them, but I cannot figure out how to disassemble this one. I removed the circlip on the back, but the shaft remains firmly within the bearing tube. Is there a hidden circlip, or is the shaft glued to the bearings?Very nice motor. It is a comparable motor to the Turnigy 2213/20. 61g with 3,5mm gold connectors and the prop holder (fixed with 3 screws). The 3 screws are not the best quality, so don't screw them too strong, or the winding will break. I have measured this motor (and the Turnigy 2213/20) with my Eagletree gear and uploaded the data to drivecalc. You can use this program to try different props. and find the right configuration. (Turnigy SK3 2830-1020 - timing med) perfect motor for quadcopters: measured for example following combination: Turnigy Platinum 40A ESC;
APC SF 10x3,8 Prop.; Voltage: 11,24V; Current: 18,76A; RPM: 7912; thrust: around 1100gOverall nice little motors, let down by poor quality control... I bought 6 for my Y6 multicopter, but 2 have very rough bearings and one of those two had poorly tapped holes on the top of the bell for mounting the alternative prop adaptor - I had to use sleeve lock and some epoxy on the adaptor to hold it firmly in place.
-
Upload
Videos -
Upload
Files -
Only registered users can upload files. Please log in or register to start helping your fellow hobbyists today!
Customer filesDrawing download now [88.64Kb]
- acc
-
-
Turnigy Aerodrive SK3 2830 Series Replacement Shaft Set
$1.14 -
Turnigy Aerodrive SK3 - 28-XX Spare Accessory Pack
Starting from: $5.22 $5.41 -
T-Prop Adaptor Set for SK3 Motors (Direct Bolt)
Special Price $0.99
You save $9.07
Was $10.06
-
Combine
essential items and
Related Products
T-Prop Adaptor Set for SK3 ...
Special Price
You save $9.07
Was