New Items Forum
Register

Total Price

$0.00

Cart 0 Cart 0 Loading...

Turnigy X6B PWM/PPM/i-BUS/SBUS Receiver 6CH 2.4G AFHDS 2A Telemetry Receiver

Turnigy X6B PWM/PPM/i-BUS/SBUS Receiver 6CH 2.4G AFHDS 2A Telemetry Receiver

Shipped From:
  • USA
  • Global
QTY:

Now save save $0.00 $0.00

$8.76
Status:
In Stock
SKU:
9114000069-0
WANT FREE SHIPPING? Click here to find out more!

The Turnigy X6B is a 6 channel two-way receiver designed for multi-rotor aircraft. It uses the 2.4GHz AFHDS 2A (Automatic Frequency Hopping Digital System) protocol and has a dual omnidirectional antenna with superior noise reduction techniques for reliable interference-free operation.

 

It’s compact, easy to install and boasts a rich easy to use interface. The X6B supports 6 channel PWM output, standard PPM output and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface.

 

This is an excellent addition to your Turnigy TGY-i6s, Turnigy Evolution or Turnigy AFDHS 9x transmitters as well as a number of other AFHDS 2A transmitters such as FS-i10, FS-i8, FS-i6, FS-i6S, FS-i6X, FS-i4 and FS-i4X.

 

An excellent receiver for multi-rotor drones as it is lightweight, cuts down on cabling and comes with built-in battery monitoring.

 

Features:
• Reliable, interference free 2.4GHz AFHDS 2A signal operation
• Channels 6 (PWM), 8 (PPM), 18 (i-bus)
• On-line Update
• The X6B receiver is compatible with all AFHDS 2A transmitters such as Turnigy TGY-i6S, Turnigy TGY-i10 and Turnigy Evolution.
• Ultra-light weight design
• Dual antennas for most reliable interference-free operation
• Reliable voltage sensing interface

 

Specs:
Channels: 6 (PWM), 8 (PPM), 18 (i-bus)
Model: Multi-Rotor
RF Range: 2.408-2.475GHz
Band width: 500kHz
Number of bands: 135
RF power: No more than 20dBm
2.4GHz protocol: AFHDS 2A
Modulation type: GFSK
Stick resolution: 1024
Low voltage alarm: Yes
DSC port: PPM / PWM / i-BUS
Antenna length: 93mm (Dual Antenna)
Power input: 4.0-8.4V DC
On-line update: Yes (wireless)
Range: >300m
Weight: 4.5g
Size: 36x22x7.5mm
Certification: CE0678, FCC ID: N4ZX6B00

  • SKU 9114000069-0
  • Brand Turnigy
  • Capacity (mAh) -
  • Shipping Weight 12.0000
  • Packaging Length 165.00
  • Packaging Width 10.00
  • Packaging Height 70.00
Upload video

Only registered users can upload video. Please, log in or register

Only registered users can write reviews. Please, sign in or sign up

Good price and good for mini quads. Also really good range.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

Good price and good for mini quads. Also really good range.

I used it for my quad setup. I used 3pin connector, connected on iBus on flight controller and it works as a charm. It has holes that 30,5mm separated, but too small diameter, so I used drill to make them 3mm, and it fit in my electronic stack above flight controller.

verified_user Quality:
playlist_add_check Overall:
trending_up Value:

I used it for my quad setup. I used 3pin connector, connected on iBus on flight controller and it works as a charm. It has holes that 30,5mm separated, but too small diameter, so I used drill to make them 3mm, and it fit in my electronic stack above flight controller.

Really good. Binds with flysky radio and gets great range. Ill get more

trending_up Value:
verified_user Quality:
playlist_add_check Overall:

Really good. Binds with flysky radio and gets great range. Ill get more

Mine came with 3 off 3 pin cables, 1 off 8 pin cable, 2 replaceable antennas and an instruction sheet. Clone of FlySky RX (PCB part FS-X6B-V1.1), so works with my FSi6 TX.
Can't find anything to complain about at this price!

trending_up Value:
verified_user Quality:
playlist_add_check Overall:

Mine came with 3 off 3 pin cables, 1 off 8 pin cable, 2 replaceable antennas and an instruction sheet. Clone of FlySky RX (PCB part FS-X6B-V1.1), so works with my FSi6 TX.
Can't find anything to complain about at this price!

Great little receiver ! Does the job !

verified_user Quality:
playlist_add_check Overall:
trending_up Value:

Great little receiver ! Does the job !

Great mini receiver for Turnigy evolution. I like that it doesn't have pins soldered so I can setup it like I want. It comes with wires for your setup. Overall this is great product.

trending_up Value:
verified_user Quality:
playlist_add_check Overall:

Great mini receiver for Turnigy evolution. I like that it doesn't have pins soldered so I can setup it like I want. It comes with wires for your setup. Overall this is great product.

I used it for my quad setup. I used 3pin connector, connected on iBus on flight controller and it works as a charm. It has holes that 30,5mm separated, but too small diameter, so I used drill to make them 3mm, and it fit in my electronic stack above flight controller.
I got 4 channels + 6 Aux channels to use. Did not test range yet, but it worked flawlessly on ~200 meters.

verified_user Quality:
playlist_add_check Overall:
trending_up Value:

I used it for my quad setup. I used 3pin connector, connected on iBus on flight controller and it works as a charm. It has holes that 30,5mm separated, but too small diameter, so I used drill to make them 3mm, and it fit in my electronic stack above flight controller.
I got 4 channels + 6 Aux channels to use. Did not test range yet, but it worked flawlessly on ~200 meters.

I had to solder to the pads on the back. GND, VCC and PPM connected and it is working correctly. Tried to solder the iBus to my FC serial port Rx with no success so switch to PPM which works.
2* quality for no cables or info on how to get them

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

I had to solder to the pads on the back. GND, VCC and PPM connected and it is working correctly. Tried to solder the iBus to my FC serial port Rx with no success so switch to PPM which works.
2* quality for no cables or info on how to get them

I had to solder to the pads on the back. GND, VCC and PPM connected and it is working correctly. Tried to solder the iBus to my FC serial port Rx with no success so switch to PPM which works.
2* quality for no cables or info on how to get them

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

I had to solder to the pads on the back. GND, VCC and PPM connected and it is working correctly. Tried to solder the iBus to my FC serial port Rx with no success so switch to PPM which works.
2* quality for no cables or info on how to get them

The X6B is a very good receiver for use with mini-quads and a AFHDS 2A transmitter like the Turnigy Evolution of FlySky i6 among others. It provides telemetry for the quad's battery voltage and has connections for i-BUS (best), PPM (OK), or PWM (LOL). It has decent range and is great for the money.

It comes with a one sheet manual and I had it bound to my TX within 10 seconds of powering on with the bind button held. I had my TX displaying battery voltage and RSSI (ERR% anyway) within a few minutes.

PROS:
- telemetry (battery voltage and ERR% which is like RSSI)
- inexpensive
- replaceable antennas (u.fl type connectors)
- small size (good for mini quads but not small enough for micro quads)
- decent range (something like 300m, will depend how you mount antennas)
CONS:
- This HK / Turnigy version doesn't come with any connectors/cables, and you will need at least 1 3-pin connector for iBus and another 3-pin connector for voltage telemetry. (PWM requires an 8-pin connector.) In contrast, the FlySky version of the X6B purchased elsewhere came with extensive cabling (3 of the 3-pin cables and an 8-pin connector, all with silicone wire).

* I wish HobbyKing would offer a cable kit for it as a listed accessory to make ordering easy. * With cables included this would be a 5-star value.

playlist_add_check Overall:
trending_up Value:
verified_user Quality:

The X6B is a very good receiver for use with mini-quads and a AFHDS 2A transmitter like the Turnigy Evolution of FlySky i6 among others. It provides telemetry for the quad's battery voltage and has connections for i-BUS (best), PPM (OK), or PWM (LOL). It has decent range and is great for the money.

It comes with a one sheet manual and I had it bound to my TX within 10 seconds of powering on with the bind button held. I had my TX displaying battery voltage and RSSI (ERR% anyway) within a few minutes.

PROS:
- telemetry (battery voltage and ERR% which is like RSSI)
- inexpensive
- replaceable antennas (u.fl type connectors)
- small size (good for mini quads but not small enough for micro quads)
- decent range (something like 300m, will depend how you mount antennas)
CONS:
- This HK / Turnigy version doesn't come with any connectors/cables, and you will need at least 1 3-pin connector for iBus and another 3-pin connector for voltage telemetry. (PWM requires an 8-pin connector.) In contrast, the FlySky version of the X6B purchased elsewhere came with extensive cabling (3 of the 3-pin cables and an 8-pin connector, all with silicone wire).

* I wish HobbyKing would offer a cable kit for it as a listed accessory to make ordering easy. * With cables included this would be a 5-star value.

  1. 1
  2. 2
Customer files
Manual Download [765]
Manual Download [765]
Upload your file

Only registered users can upload files.
Please log in or register to start helping your fellow hobbyists today!

Combine Essential Items and Save